Винтовые

List of parts for SAB 85

0662-821 rev 99.12

List of parts for SAB 85

Relevant drawing document: 0662-820

Pos.nr

Designation

No.

Part no.

Rotor housing, unclassified

3011-031

Bearing housing unclassified

3013-259

Dowel pin

2122-027

Pair of rotors, unclassified

3024-135

Gasket

2353-201

Distance washer

3049-074

Radial bearing 2318

1513-061

Radial bearing 2317

1513-062

Radial bearing 2314

1513-063

Thrust bearing 7317

1513-057

Thrust bearing 7315

1513-064

Nut M85x2

1514-021

Nut M75x1,5

1514-024

Shaft seal

1332-033

Snap Ring

3026-045

Spacer sleeve

3049-075

Spacer sleeve

3049-079

Bearing cover

3013-261

Gasket

2353-204

Seat holder

3026-042

Oil collector

3026-043

Gasket

2353-193

Pipe

3026-044

Pipe nr. 3026-044 Replaced by : hose

1345.143

Draining hose nr 1904 211-5 union V¼"

Adjusting screw

3049-051

Protecting washer

3049-052

Shims

2212-140

Balancing piston

3025-045

Orifice plug Ø1

3049-067

Cover

3013-262

Slide valve

3049-083

Slide valve

3049-076

Guide block

3049-077

Cover-Slide valve

3013-263

Holder

3049-054

Magnet

3043-196

Cover-Bearing housing

3013-264

Dowel pin

3049-055

Cylinder

3043-185

Cylinder head

3013-245

Hydraulic piston

3043-186

1) only for high pressure compressor
2) only for booster compressor
3) compressor with economiser
4) compressor without economiser

Pos.nr	Designation	No.	Part no.
50	Piston rod	1	3043-201
51	Probe	1	3045-068
52	Spring housing	1	3049-056
53	Gland	1	3043-192
54	Washer	1	3043-193
55	Unloading spring	1	3043-194
56	Support ring	1	2353-199
57	Vi-piston	1	3044-084	6)
58	Vi-cylinder	1	3044-085	5)
59	Cover, Vi-cylinder	1	3013-265	5)
60	Gasket	1	2353-202
61	Hydraulic piston	1	3044-086	5)
62	Piston rod	1	3044-078	5)
63	Indicator	1	3044-079	5)
64	Dowel pin	1	3044-080	6)
66	Support ring	1	2353-200	5)
67	Pilot valve	1	1372-208	5)
68	Cover	1	3013-250	5)
69	Gasket	1	2353-195
70	Control piston	1	3044-081	5)
71	Spring	1	3044-083	5)
72	Blind cover	1	3013-257	7)
73	Distance plug	1	3049-078
75	Suction filter	1	1517-132
76	Gasket	2	2353-203
77	Filter holder	1	3042-118
78	Suction filter cover	1	3013-266
79	Guide	1	3042-117
81	Blind cover	1	1906675-1	7)
82	Distance ring	1	1906676-1	8)
84	Cover	1	3013-252
85	Cover	1	3013-253
86	Cover	1	3013-254
87	Cover	1	3013-255
88	Gasket	1	2353-197
89	Orifice plug Ø6,5	2	3044-087
95	Oil pump	1	1524-221
96	Gasket	1	2353-198
87	Oil pump holder	1	3041-016
99	Reducing piston	1	3041-014
109	Stop valve	2	1374-011
110	Stop valve	2	1374-012

5) Only for compressors with variable Vi
6) Only for compressors with variable Vi or fixed Vi =4.8
7) Only for compressors with fixed Vi =2.6 or 4.8
8) Only for compressors with fixed Vi =4.8

Pos.nr	Designation	No.	Part no.
112	Compressor sign	1	2516-301
114	Warning sign	1	2516-302
116	Drive screw	8	1414-200
120	Blind flange DN 25	1	1344-302
122	Blind flange DN 50	1	1344-304
123	Blind flange DN 65	1	1344-303
124	Gasket 43/57x2	1	2356-065
126	Gasket 73/87x2	1	2356-221
127	Gasket 95/109x2	1	2356-222
128	Spiral pin 3x10	2
130	Spiral pin 6x16	2	1446-038
131	Parallel pin CPK 10x35	2	1445-082
132	Parallel pin 10x30	9(7)	1445-081	9)
134	Parallel pin 10x110	1	1445-087	5)
135	Parallel pin 10x120	1	1445-085	5)
138	Tension pin 6x32	1	1446-039
139	Grooved pin 4x14	1	1446-041
141	Retaining ring SgH 40	1	1437-150	5)
142	Retaining ring SgH 70	1	39 215 460 152
143	Retaining ring SgH 80	1	1437-160
145	Retaining ring SgA 70	1	1437-242	1)
146	Retaining ring SgA 90	1	1437-245
148	Disc spring	4	1523-056	8)
149	Disc spring	2	1523-039
150	Disc spring	8	1523-048
151	Disc spring	1	1523-052
152	Pressure spring	1	1523-053
153	Pressure spring	2	1523-037
155	Plug 1/16"	9(2)	1343-021	9)
156	Plug 1/8"	11(10)	1343-022	9)
158	Plug 3/8"	16	1343-023
160	Plug G1/4"	2	1343-025
161	Plug G1/2"	6	1343-027
162	Plug G3/4"	9	1437-028
163	Plug G1"	3	1343-030
165	Gasket 14/21	2	2356-320
166	Gasket 21/28	6	2356-321
167	Gasket 27/33	10	2356-322
168	Gasket 34/42	3	2356-323
169	Gasket 34/43x2,5	1	2356-324

2) Only for booster compressor
5) Only for compressors with variable Vi
8) Only for compressors with fixed Vi =4.8
9) No. in () for compressors with fixed Vi

Pos.nr	Designation	No.	Part no.
170	Slide ring	1	1243-022	5)
171	Slide ring	1	1243-023
173	Sealing ring	1	1332-034
174	Sealing ring	1	1332-037	5)
175	Sealing ring	1	1332-043
176	Sealing ring	1	1332-063	5)
177	Sealing ring	1	1332-046
180	Sight glass	1	1226-029
181	Check valve	1	1364-200
182	Check valve	1	1364-197
184	V-ring	1	1332-036
187	O-ring 10,3x2,4	1	1331-343
188	O-ring 15,3x2,4	3	1331-344
191	O-ring 19,2x3	1	1331-345
192	O-ring 24,2x3	1	1331-346	5)
193	O-ring 29,2x3	2	1331-347	5)
194	O-ring 39,2x3	1	1331-348	5)
195	O-ring 44,2x3	2	1331-349
196	O-ring 49,5x3	2	1331-350
197	O-ring 54,5x3	1	1331-351
199	O-ring 69,5x3	1	1331-352
200	O-ring 79,5x3	1	1331-353	5)
203	O-ring 109,5x3	1	1331-354
204	O-ring 114,5x3	2	1331-355
206	O-ring 129,5x3	1	1331-358
207	O-ring 49,2x5,7	2(1)	1331-359	9)
208	O-ring 134,5x3	1	1331-364
209	O-ring 144,5x3	2	1331-365	5)
210	O-ring 164,3x5,7	2	1331-366
211	O-ring 249,3x5,7	1	1331-367
214	Hexagon screw M 12x35	4	1413-387
216	Hexagon screw M 16x45	28	1413-433
219	Lifting eye M30	2	1427-160
223	Grub screw 6x16	2	1413-231
228	Hex. socket screw 5x30	4	1413-035
230	Hex. socket screw 6x16	6	1413-340
231	Hex. socket screw 10x20	4	1413-370
232	Hex. socket screw 10x25	15	1413-371
233	Hex. socket screw 10x30	9(7)	1413-372	9)

5) Only for compressors with variable Vi
9) No. in () for compressors with fixed Vi

Pos.nr	Designation	No.	Part no.
234	Hex. socket screw 10x35	23	1413-373
235	Hex. socket screw 10x40	9	1413-374
236	Hex. socket screw 10x45	2	3921 2179 500
238	Hex. socket screw 10x90	5	1413-380
239	Hex. socket screw 10x110	3	1413-393	5)
241	Hex. socket screw 12x30	17	1413-386
242	Hex. socket screw 12x35	4	1413-387
243	Hex. socket screw 12x50	6	1413-390
244	Hex. socket screw 12x65	20	1413-401
249	Hex. socket screw 16x55	28	1413-036
256	Nipple	2	1349-206
258	Nipple	1	1349-230
270	Protecting cover	1	1246-059
275	Solenoid valve with Coil 220V 50 Hz	1	1372-214	10)
	120V 60 Hz	1	1372-215	10)
	24V 50 Hz	1	1372-216	10)
	24V DC	1	1372-093	10)
	Coil 220-240V 50-60Hz	2	1921 470-1	10)
	120-110V 50-60Hz	2	1921 470-2	10)
	24V 60Hz	2	1921 470-3	10)
276	Orifice plug Ø2.0	1	1371-038
277	Orifice plug Ø2.3	1	1371-039
280	Position transmitter	1	1553-240

5) Only for compressors with variable Vi
9) No. In () for compressors with fixed Vi
10) Depending on pilot voltage

Small tool set for SAB 81- 83 - 85 - 87 - 89 compressors

This tool set contains the tools needed to align the electric motor, to replace a shaft seal, to replace a
visual indicator seal and to replace a coupling. Each compressor should be provided with this tool set.
For major overhaul work (replacing bearings e.g.), this tool set must be supplemented with the large tool
set - see doc.no. 0662-803 (SAB 81), 0662-813 (SAB 83) , 0662-823 (SAB 85) , 0662-833 (SAB 87) or
0662-843 (SAB 89).

List of tools in the tool set 3083.189

Item	Designation	quantity	Article no.
1	Tool box	1	1906 139-1
2	Alignment device for coupling	1	3183.105
3	Feeler gauge (incl. In 3183.105)	2	1622.050
4	Level arm	1	1906 152-1
5	Puller screw	2	1906 153-1
6	Guiding pin	2	1906 154-1
7	Dismantling tool	1	1906 155-1
8	Puller screw	2	1905 156-1
9	Guide	1	1906 157-A
15	Screw M 14x40	2	1906 140-15
16	NutM12	2	1906 140-16
17	NutM6	2	1906 140-17
18	Hexagon key 4 mm	1	1906 140-18
19	Hexagon key 5 mm	1	1906 140-19
20	Hexagon key 12 mm	1	1906 140-20
21	Socket-head sleeve 6 mm	2	1906 140-21
22	Socket-head sleeve 8 mm	1	1906 140-22
23	Socket-head sleeve 10 mm	1	1906 140-23

Large tool set for SAB 85 compressors

The tools specified below are needed for major overhauls and repairs (e.g. service after 40 000 operating
hours or changing bearings). These tools named the large tool set must be supplemented with the so-
called sma// too/ set article no. 3083.189. See Document no. 0662-804

List of tools in the tool set 1906 145-A

Item	Designation	quantity	Article no.
1	Tool box	1	1906 145-1
2	Sleeve for bearing nut .screw	1	1906380-A
3	Sleeve for bearing nut, slide	1	1906381-A
4	Yoke	1	1906390-1
5	Level arm	1	1906391-1
6	Holder	2	1906354-A
7	Holder	1	1906355-A
8	Holder	1	1906356-A
9	Tie rod	2	1906 136-1
10	Tie rod	1	1906 137-1
12	Dismounting tool for radial bearing	1	1906072-1
13	Dismounting tool for radial bearing	1	1906076-1
14	Dismounting tool for radial bearing	1	1906093-1
15	Sleeve	1	1906098-1
16	Assembling tool for bearing	1	1906384-1
17	Washer	1	1906385-1
18	Adapte	1	1906386-1
20	Guide	1	1906388-1
21	Guide	1	1906389-1
22	Level arm	1	1906 138-1
23	Guide	1	1906378-1
24	Guide	1	1906378-2
25	Guide	1	1906378-3
26	Guide	1	1906392-1
32	Feeler gauge	1	1878747-A
33	Retaining-ring pliers	1	1906 145-33
34	Socket head sleeve	1	1906 145-34
35	Socket head sleeve	1	1906 145-35
36	Socket head sleeve	1	1906 145-36
37	Socket head sleeve	1	1906 145-37
38	Adapter	1	1906 145-38
40	Hexagon socket screw key	1	1906 145-40
41	Ratched-ring key	1	1906 145-41
42	Flange nut	2	1906 145-42
43	Flange nut	1	1906 145-43
45	Thrust bearing	1	1906 145-45
47	Lifting eye	1	39 218 333 534
48	Lifting eye	1	39 218 333 670
50	Screw	4	39 212 120 532
51	Hexagon screw	1	1906 145-51
52	Hexagon screw	1	1906 145-52
55	Grub screw	1	1906 145-55
60	Guide	2	1905777-1

Spare Parts for service on
SAB 85 compressor

The spare parts listed below are needed for the following service jobs. For separate gaskets or
items -see part list for compressor Document no.0662-821
The relevant drawing document: 0662-820

	No.	Designation	Pos.no.	Remarks
Cleaning of suction filter Part no. 3084-715	2 2 1	Gasket Gasket O-ring	76 126 211	D=73/87x2 249,3x5,7

	No.	Designation	Pos.no.	Remarks
Change of seal for visual position indicator Part no. 3084-706	1 1 1 1 1	Sealing ring Support ring O-ring O-ring O-ring	173 56 191 195 206	9,2x3 44,3x3 129,5x3


	No.	Designation	Pos. no.	Remarks
Change of seal for indication of Vi-piston Part no. 3084-707	1 1 1 1	Sealing ring Support ring O-ring O-ring	174 66 193 203	29,2x3 109.5x3

	No.	Designation	Pos.no.	Remarks
Inspection of rotors Part no. 3084-718	1 2 1 2 1	Gasket Gasket Gasket Gasket O-ring	60 76 88 126 211	D=87/73x2 249.3x5,7

	No.	Designation	Pos. no.	Remarks
Change of oil pump Part no. 3084-717	1 1 2	Oil pump Gasket Tension pin	95 96 130	6x16

	No.	Designation	Pos. no.	Remarks
Change of shaft seal Part no. 3084-716	1 1 1 1 1 1	Shaft seal O-ring O-ring V-ring Gasket Gasket	18 203 204 184 27 167	109.5x3 114.3x3

	No.	Designation	Pos. no.	Remarks
Capacity control	1	Complete solenoid valve but without orifices	1921 438-1	240 V/60 Hz 220 V/50 Hz
	1
	1		1921 438-2	120 V/60 Hz 110 V/50 Hz
	1
	1		1921 438-3	24 V/50-60 Hz
	2	Coil	1921 470-1	240 V/60 Hz 220 V/50 Hz
	2
	2		1921 470-2	120 V/60 Hz 110 V/50 Hz
	2
	2		1921 470-3	24 V/50-60 Hz
	1 1 4	Orifice conn. P Orifice conn. T O-ring	277 276	Ø2,3 mm Ø 2,0 mm 9,25x1,78



	No.	Designation	Pos.no.	Remarks
Change of bearing or complete overhaul Part no. 3084-547	1	Set of gaskets		3084-702
	1	Radial bearing	11
	1	Radial bearing	12
	2	Radial bearing	13
	3	Thrust bearing	14
	2	Thrust bearing	15
	1	Shaft seal kit	18	3084-716
	1	Shim	34	0.1

List of parts for SAB 87

0662-831 rev. 00.06

List of parts for SAB 87

Relevant drawing document: 0662-830

Pos.nr	Designation	No.	Part no.
2	Rotor housing, unclassified	1	3011-030
4	Bearing housing unclassified	1	3013-240
5	Dowel pin	2	2122-027
7	Pair of rotors, unclassified	1	3024-129
8	Gasket	1	2353-191
10	Distance washer	1	3049-050
11	Radial bearing 2320	1	1513-053
12	Radial bearing 2319	1	1513-054
13	Radial bearing 2316	2	1513-055
14	Thrust bearing 7318	3	1513-056
15	Thrust bearing 7317	2	1513-057
16	Nut M85x2	1	1514-021
18	Shaft seal	1	1332-033
19	Snap Ring	1	3026-045
20	Spacer sleeve	1	3049-048
21	Spacer sleeve	1	3049-049
23	Bearing cover	1	1906420-1
24	Gasket	1	2353-192
25	Seat holder	1	3026-042
26	Oil collector	1	3026-043
27	Gasket	1	2353-193
29	Pipe	1	3026-044
32	Adjusting screw	3	3049-051
33	Protecting washer	1	3049-052
34	Shims	1	2212-139
36	Balancing piston	1	3025-044
38	Cover	1	3013-242
39	Slide valve	1	3049-057
40	Slide valve	1	3049-082
41	Guide block	1	3049-053
42	Cover-Slide valve	1	3013-243
43	Holder	1	3049-054
44	Magnet	2	3043-196
45	Cover-Bearing housing	1	3013-224
46	Dowel pin	2	3049-055
47	Cylinder	1	3043-185
48	Cylinder head	1	3013-245
49	Hydraulic piston	1	3043-186

1) only for high pressure compressor
2) only for booster compressor
3) compressor with economiser
4) compressor without economiser

Pos.nr	Designation	No.	Part no.
50	Piston rod	1	3043-188
51	Probe	1	3045-068
52	Spring housing	1	1906447-A
53	Gland	1	3043-192
54	Washer	1	3043-193
55	Unloading spring	1	3043-194
56	Support ring	1	2353-199
57	Vi-piston	1	3044-075	6)
58	Vi-cylinder	1	3044-076	5)
59	Cover, Vi-cylinder	1	3013-249	5)
60	Gasket	1	2353-194
61	Hydraulic piston	1	3044-077	5)
62	Piston rod	1	3044-078	5)
63	Indicator	1	3044-079	5)
64	Dowel pin	1	3044-080	5)
66	Support ring	1	2353-200	5)
67	Pilot valve	1	1372-208	5)
68	Cover	1	3013-250	5)
69	Gasket	1	2353-195
70	Control piston	1	3044-081	5)
71	Spring	1	3044-083	5)
72	Blind cover	1	3013-257	7)
75	Suction filter	1	3042-115
76	Gasket	2	2353-196
77	Filter holder	1	3042-116
78	Suction filter cover	1	3013-251
79	Guide	1	3042-117
81	Blind cover	1	3013-258	7)
82	Distance ring	1	2124-096	8)
84	Cover	1	3013-252
85	Cover	1	3013-253
86	Cover	1	3013-254
87	Cover	1	3013-255
88	Gasket	1	2353-197
89	Orifice plug Ø8.0	2	3044-082
95	Oil pump	1	1524-221
96	Gasket	1	2353-198
97	Oil pump holder	1	3041-013
99	Reducing piston	1	3041-014
109	Stop valve	2	1374-011
110	Stop valve	2	1374-012

5) Only for compressors with variable Vi
6) Only for compressors with variable Vi or fixed Vi =4.8
7) Only for compressors with fixed Vi =2.6 or 4.8
8) Only for compressors with fixed Vi =4.8

Pos.nr	Designation	No.	Part no.
112	Compressor sign	1	2516-301
114	Warning sign	1	2516-302
115	Stal sign	1	2516-303
116	Drive screw	8	1414-200
120	Blind flange DN 25	1	1344-302
123	Blind flange DN 65	2	1344-303
124	Gasket 43/57x2	1	2356-065
127	Gasket 95/109x2	2	2356-222
128	Spiral pin 3x10	2	1446-037
130	Spiral pin 6x16	2	1446-038
131	Parallel pin CPK 10x35	2	1445-082
132	Parallel pin 10x30	9(7)	1445-081	9)
134	Parallel pin 10x120	1	1445-085	5)
135	Parallel pin 10x140	1	1445-086	5)
138	Tension pin 6x32	1	1446-039
139	Grooved pin 4x14	1	1446-041
141	Retaining ring SgH 40	1	1437-150	5)
142	Retaining ring SgH 70	1	1437-159
143	Retaining ring SgH 110	1	1437-169
145	Retaining ring SgA 80	1	1437-230	1)
146	Retaining ring SgA 100	1	1437-244
148	Disc spring	4	3921 9512357	8)
149	Disc spring	2	1523-039
150	Disc spring	8	1523-048
151	Disc spring	1	1523-052
152	Pressure spring	1	1523-053
153	Pressure spring	2	1523-037
155	Plug 1/16"	9(2)	1343-021	9)
156	Plug 1/8"	11(10)	1343-022	9)
158	Plug 3/8"	16	1343-023
160	Plug G1/4"	2	1343-025
161	Plug G1/2"	6	1343-027
162	Plug G3/4"	9	1343-028
163	Plug G1"	3	1343-030
165	Gasket 14/21	2	2356-320
166	Gasket 21/28	6	2356-321
167	Gasket 27/33	10	2356-322
168	Gasket 34/42	3	2356-323
169	Gasket 34/43x2,5	1	2356-324

2) Only for booster compressor
5) Only for compressors with variable Vi
8) Only for compressors with fixed Vi =4.8
9) No. in ( ) for compressors with fixed Vi

Pos.nr	Designation	No.	Part no.
170	Slide ring	1	1243-020	5)
171	Slide ring	1	1243-020
173	Sealing ring	1	1332-034
174	Sealing ring	1	1332-037	5)
175	Sealing ring	1	1332-039
176	Sealing ring	1	1332-041	5)
177	Sealing ring	1	1332-042
180	Sight glass	1	1226-029
181	Check valve	1	1364-200
182	Check valve	1	1364-197
184	V-ring	1	1332-036
187	O-ring 10,3x2,4	1	1331-343
188	O-ring 15,3x2,4	3	1331-344
191	O-ring 19,2x3	1	1331-345
192	O-ring 24,2x3	1	1331-346	5)
193	O-ring 29,2x3	1	1331-347	5)
194	O-ring 39,2x3	1	1331-348	5)
195	O-ring 44,2x3	2	1331-349
196	O-ring 49,5x3	2	1331-350
197	O-ring 54,5x3	1	1331-351
199	O-ring 69,5x3	1	1331-352
200	O-ring 79,5x3	1	1331-353
203	O-ring 109,5x3	2	1331-354
204	O-ring 114,5x3	1	1331-355
205	O-ring 124,5x3	1	1331-357
206	O-ring 129,5x3	1	1331-358
207	O-ring 49,2x5,7	2(1)	1331-359	9)
208	O-ring 149,3x5,7	1	1331-360
209	O-ring 159,3x5,7	2	1331-361
210	O-ring 184,3x5,7	2	1331-362
211	O-ring 279,3x5,7	1	1331-363
214	Hexagon screw M 12x35	4	3921 2120538
216	Hexagon screw M 16x45	32	1413-433
223	Grub screw 6x16	2	1413-231
228	Hex. socket screw 5x30	4	1413-035
230	Hex. socket screw 6x16	6	1413-340
231	Hex.socket screw 10x25	4	1413-371
232	Hex. socket screw 10x25	15	1413-371
233	Hex.socket screw 10x30	9(7)	1413-372	9)

5) Only for compressors with variable Vi
9) No. in ( ) for compressors with fixed Vi

Pos.nr	Designation	No.	Part no.
234	Hex. socket screw 10x35	23	1413-373
235	Hex. socket screw 10x40	10	1413-374
236	Hex. socket screw 10x45	2	1413-375
238	Hex. socket screw 10x90	5	1413-380
239	Hex. socket screw 10x110	3	1413-393	5)
241	Hex. socket screw 12x30	17	1413-386
242	Hex. socket screw 12x35	4	1413-387
243	Hex. socket screw 12x50	8	1413-390
244	Hex. socket screw 12x65	24	1413-401
249	Hex. socket screw 16x55	32	1413-036
256	Nipple	2	1343-023
258	Nipple	1	1349-230
270	Protecting cover	1	1246-059
275	Solenoid valve	1	1372-216
276	Orifice plug 02.0	1	1371-038
277	Orifice plug 02.5	1	1371-039
280	Position transmitter	1	1553-220

5) Only for compressors with variable Vi

9) No. In ( ) for compressors with fixed Vi

Large tool set for SAB 87 compressors

The tools specified below are needed for major overhauls and repairs (e.g. service after 40 000 operating

hours or changing bearings). These tools named the large tool set must be supplemented with the so-

called small tool set article no. 3083.189. See Document no. 0662-804

List of tools in the tool set 1906 147-A

Item	Designation	quantity	Article no.
1	Tool box	1	1906 147-1
2	Sleeve for bearing nut .screw	1	1906380-A
3	Sleeve for bearing nut, slide	1	1906481-A
4	Yoke	1	1906490-1
5	Level arm	1	1906491-1
6	Holder	2	1906454-A
7	Holder	1	1906455-A
8	Holder	1	1906456-A
9	Tie rod	2	1906 136-1
10	Tie rod	1	1906 137-1
12	Dismounting tool for radial bearing	1	1906075-1
13	Dismounting tool for radial bearing	1	1906094-1
14	Dismounting tool for radial bearing	1	1906095-1
15	Sleeve	1	1906098-1
16	Assembling tool for bearing	1	1906484-1
17	Washer	1	1906485-1
18	Adapter	1	1906486-1
20	Guide	1	1906488-1
21	Guide	1	1906489-1
22	Level arm	1	1906 138-1
23	Guide	1	1906478-1
24	Guide	1	1906478-2
25	Guide	1	1906478-3
26	Guide	1	1906492-1
32	Feeler gauge	1	1878747-A
33	Retaining-ring pliers	1	1906 147-33
34	Socket head sleeve	1	1906 147-34
35	Socket head sleeve	1	1906 147-35
36	Socket head sleeve	1	1906 147-36
37	Socket head sleeve	1	1906 147-37
38	Adapter	1	1906 147-38
40	Hexagon socket screw key	1	1906 147-40
41	Ratched-ring key	1	1906 147-41
42	Flange nut	2	1906 144-42
43	Flange nut	1	1906 147-43
45	Thrust bearing	1	1906 147-45
47	Lifting eye	1	39 218 333 534
48	Lifting eye	1	39 218 333 670
50	Screw	4	39212120532
51	Hexagon screw	1	1906 147-51
52	Hexagon screw	1	1906 147-52
55	Grub screw	1	1906 147-55
60	Guide	2	1905777-1

Small tool set for SAB 81- 83 - 85 - 87 - 89 compressors

This tool set contains the tools needed to align the electric motor, to replace a shaft seal, to replace a

visual indicator seal and to replace a coupling. Each compressor should be provided with this tool set.

For major overhaul work (replacing bearings e.g.), this tool set must be supplemented with the large tool

set - see doc.no. 0662-803 (SAB 81), 0662-813 (SAB 83) , 0662-823 (SAB 85) , 0662-833 (SAB 87) or

0662-843 (SAB 89).

List of tools in the tool set 3083.189

Item	Designation	quantity	Article no.
1	Tool box	1	1906139-1
2	Alignment device for coupling	1	3183.105
3	Feeler gauge (incl. In 3183.105)	2	1622.050
4	Level arm	1	1906 152-1
5	Puller screw	2	1906 153-1
6	Guiding pin	2	1906 154-1
7	Dismantling tool	1	1906 155-1
8	Puller screw	2	1905 156-1
9	Guide	1	1906 157-A
15	Screw M 14x40	2	1906 140-15
16	NutM12	2	1906 140-16
17	NutM6	2	1906 140-17
18	Hexagon key 4 mm	1	1906 140-18
19	Hexagon key 5 mm	1	1906 140-19
20	Hexagon key 12 mm	1	1906 140-20
21	Socket-head sleeve 6 mm	2	1906 140-21
22	Socket-head sleeve 8 mm	1	1906 140-22
23	Socket-head sleeve 10 mm	1	1906 140-23

Spare Parts for service on SAB 87 compressor

The spare parts listed below are needed for the following service jobs. For separate gaskets or
items -see part list for compressor Document no.0662-831
The relevant drawing document: 0662-830

Cleaning of suction filter Part no. 3084-719	No.	Designation	Pos. no.	Remarks
	2	Gasket	76
	2	Gasket	127	D= 109/95x2
	1	O-ring	211	279,3x5,7

Change of seal for visual position indicator Part no. 3084-706	No.	Designation	Pos. no.	Remarks
	1	Sealing ring	173
	1	Sealing ring	56
	1	O-ring	191	19,2x3
	1	O-ring	195	44,3x3
	1	O-ring	206	129,5x3

Change of seal for indication ofVi-piston Part no. 3084-707	No.	Designation	Pos.no.	Remarks
	1	Sealing ring	174
	1	Support ring	66
	1	O-ring	193	29,2x3
	1	O-ring	205	124.5x3

Inspection of rotors Part no. 3084-720	No.	Designation	Pos. no.	Remarks
	1	Gasket	60
	2	Gasket	76
	1	Gasket	88
	2	Gasket	127	D= 109/95x2
	1	O-ring	211	279.3x5,7

Change of oil pump Part no. 3084-717	No.	Designation	Pos. no.	Remarks
	1	Oil pump	95
	1	Gasket	96
	2	Tension pin	130	6x16

Change of shaft seal Part no. 3084-716	No.	Designation	Pos.no.	Remarks
	1	Shaft seal	18
	1	O-ring	203	109.5x3
	1	O-ring	204	114.3x3
	1	V-ring	184
	1	Gasket	27
	1	Gasket	167

Capacity control	1	Complete solenoid valve but without orifices	1921 438-1	240 V/60 Hz
			1921 438-1	220 V/50 Hz
	1		1921 438-2	120 V/60 Hz
			1921 438-2	110 V/50 Hz
	1		1921 438-3	24 V/50-60 Hz
	2	Coil	1921 470-1	240 V/60 Hz
			1921 470-1	220 V/50 Hz
	2		1921 470-2	120 V/60 Hz
			1921 470-2	110 V/50 Hz
	2		1921 470-3	24 V/50-60 Hz
	1	Orifice conn. P	277	Ø2,3mm
	1	Orifice conn. T	276	Ø2,0mm
	4	O-ring		9,25x1,78

Change of bearing or complete overhaul Part no. 3084-548	No.	Designation	Pos.no.	Remarks
	1	Set of gaskets		3084-701
	1	Radial bearing	11
	1	Radial bearing	12
	2	Radial bearing	13
	3	Thrust bearing	14
	2	Thrust bearing	15
	1	Shaft seal kit	18	3084-716
	1	Shim	34	0.1

List of parts for SAB 110


List of parts for SAB 110

Relevant drawing 0661-644

Pos.	Designation	No.	Part no
	Complete compressor, male drive:
	SAB 110 SM		4161-050
	SAB 110SM for HLI/ECO		4161-054
	SAB 110 LM		4161-052
	SAB 110 LM for HLI/ECO		4161-056
	Complete compresssor, female drive:
	SAB 110 SF		4161-051
	SAB 110 SF for HLI/ECO		4161-055
	SAB 110 LF		4161-053
	SAB 110 LF for HLI/ECO		4161-057
	Compressor housing
10-1	Compressor housing (S) not prepared for HLI and ECO	1	3011-016
10-2	Compressor housing (L) not prepared for HLI and ECO	1	3011-007
10-3	Compressor housing (S) prepared for HLI and ECO	1	3011-018
10-4	Compressor housing (L) prepared for HLI and ECO	1	3011-017
	Bearing cover at suction end
20-1	Bearing cover, female drive	1	3013-082
20-2	Bearing cover, male drive	1	3013-083
21	O-ring dia. 254.00 x 3.53	1	1331-113
22	Cylindrical pin. dia. 12 x 40	2	1445-084
23	Socket cap screw M12 x 35	10	1413-387
24	Threaded plug with collar 1/2"	1	1343-027
25	Gasket dia. 27/21x1.5	1	2356-133
30	Suction port for male drive	1	3031-019
31	Suction port for female drive	1	3031-020
32	Cylinder screw M8 x 25	3	1413-357
33	Cylinder screw M8 x 35	1	1413-359
	Bearing cover at discharge end
40	Cover	1	3013-075
43	Cylinder screw M 10 x 30	4	1413-372
44	Adjusting screw M20	2	2111-122
45	Locking screw M6 x 10	4	1413.231
0061 -845

Pos.	Designation	No.	Part no
	Capacity regulating cylinder
50	Cylinder	1	3043-098
51	O-ring dia. 66,27 x 3,53	1	1331-072
52	Cylinder screw M10 x 30	3	1413-372
	Cover for capacity regulating cylinder
60	Cover	1	3013-193
61	O-ring dia. 88,49 x 3,53	1	1331-079
62	Cylinder screw M8 x 35	4	1413-359
	Housing for capacity indicator
70	Housing	1	3045-002
71	Cylinder screw M6 x 30	4	1413-343
72	Cover for capacity indicator	1	3045-003
73	Cylinder screw M6 x 50	4	1413-347
74	O-ring dia. 98,02 x 3,53	1	1331-081
75-1	Glass for indicator (L)	1	3045-013
75-2	Glass for indicator (S)	1	3045-012
83	Driving pin dia. 4 x 6 for shaft seal cover	1	1446-011
	Slide stop
101	Sealing ring	1	1332-121
103	Piston	1	3043-101
105	Retainer	1	3043-102
106	Cylinder screw M6 x 25	2	1413-342
107	Threaded plug G 1/8"	1	1343-024
108	Gasket dia. 16/10	1	2356-216
	Rotors and bearings
110-1	Set of rotors for SM	1	3024-112
110-2	Set of rotors for SF	1	3024-082
110-3	Set of rotors for LM	1	3024-115
110-4	Set of rotors for LF	1	3024-080
111	Roller bearing	4	1512-001
114	Thrust washer	2	3021-019
115	Cylinder screw M10 x 35	2	1413-373
119	Retainer pin for male and female rotor bearing	2	3021-017
130	Balance piston	2	3025-014
132	Four point bearing	2	1513-039
0661-845

Pos.	Designation	No.	Part no
133	Set of shims dia. 63/80 for adjusting the clearance	2	2124-079
	between the rotor and outlet ports comprising:
	1 off 0,82 mm
	1 off 0,85 mm
	1 off 0,88 mm
	1 off 0,91 mm
	1 off 0,94 mm
	1 off 0,97 mm
	1 off 1,00mm
139	Ring for balance piston	2	3025-030
	Discharge ports
140	Discharge port for male rotor	1	3031-029
141	Discharge port for female rotor	1	3031-030
142	Socket cap screw M8 x 110	6	1413-311
143	Sealing ring dia. 13/8	6	3049-006
	Parts for adjusting rotors
153	Thrust cover	2	3013-080
154	O-ring dia. 72,62 x 3,53	2	1331-074
	Shaft seal
160	Shaft seal, complete	1	1332-178
162	O-ring dia. 50,39 x 3,53 (included in DOS. 160)		1331-067
163	0-ring dia. 34,52x3,53	1	1331-028
165	Cover for shaft seal	1	3013-084
166	O-ring dia. 72,62 x 3,53	1	1331-074
167	Cylinder screw M8 x 25	4	1413-375
168	Balancing piston	1	3025-015
	Suction filter
170	Suction filter	1	3042-082
	Adjusting system for Vpslide
180	Adjusting screw M8 x 90	1	1424-180
181	Nut	2	1432-063
	Vi-slide
190	Slide	1	3044-026
191-1	Spring for SAB110 L	1	2144-046
191-2	Spring for SAB 110 S	1	2144-045
0661-845

Pos.	Designation	No.	Part no
	Capasity regulating slide
200-1	Slide for L	1	3043-097
200-2	Slide for S	1	3043-104
201	Piston part	2	3043-100
203	O-ring dia. 23,39 x 3,53	1	1331-021
204	Sealing ring	1	1332-120
205	Cylinderical pin dia. 6x12	1	1445-075
206	Slotted nut	1	1514-198
207-1	Piston rod for L	1	3043-121
207-2	Piston rod for S	1	3043-122
208	Locking plate	1	1514-068
	Spindle for capacity indication
210-1	Spindle	1	3045-057
216	Magnetic coupling	1	3045-061
217	O-ring dia.44,12.x 2,62 (incl. in pos. 216)	(1)	1331-146
218	Hexagon head screw M4 x 16 (incl. in pos. 216)	(1)	1413-320
219	Hexagon head screw M4 x 20 (incl. in pos. 216)	(2)	1413-322
	Capacity indication
221	Indication dial	1	3045-001
223	Socket cap screw M4 x 10	1	1413-319
224	Backing ring	1	2356-155
226	Locking washer DL 15/84	1	1437-054
227	Locking washer DC 8/4,3	1	1437-060
	Economizer HLI inlet
235	Threaded plug with collar 1/2"	2	1343-027
236	Gasket dia. 27/21 x1,5	2	2356-133
	To connect the economizer line to the compressor use: Connection for pipe dia. 18/15	1	1349-130
	Suction gas inlet
252	0-ring dia. 107,54 x 3,53	1	1331-085
253	Seat for suction valve	4	3013-120
254	Cylinder screw M12 x 35	4	1413-387
255-1	Welding flange DN 50	1	2342-172
255-2	Welding flange DN 65	1	2342-173
0661-845

Pos.	Designation	No.	Part no
255-3	Welding flange DN 80	1	2342-174
256	O-ring dia. 91,67 x 3,53	1	1331-080
257	Al-gasket dia. 19/14 x 1,5	1	2356-124
258	Threaded plug with collar 1/4"	1	1343-025
	Non-return valve
260	Piston for non-return valve	1	3042-039
261	Spring	1	2144-038
262	Locking ring	2	1437-291
263	Guide for piston	1	3042-040
	Valve cone (optional for twin/triple units only)
265	Spindle	1	3042-050
266	Gasket ring dia. 66/56 x 2	1	2354-174
267	Cone ring	1	3042-051
268	Nut M16	1	1432-307
	Suction side throtting system
270	Cylinder	1	3042-038
271	Piston	1	3042-042
272	Spring	1	2144-037
273	O-ring dia. 107,54 x 3,53	1	1331-085
	Connecting parts for slide rod
311-1	Cylinder screw M8 x 50 (type L)	1	1413-368
311-2	Cylinder screw M8 x 40 (type S)	1	1413-360
	External oil piping
320-1	Connecting pipe set, SAB 110 SM	1	3049-014
320-2	Connecting pipe set, SAB 110 SF	1	3049-013
320-3	Connecting pipe set, SAB 110 LM	1	3049-010
320-4	Connecting pipe set, SAB 110 LF	1	3049-011
325-1	Orifice for oil injection - dia. 6 (R717)	1	3043-107
325-2	Orifice for oil injection - dia. 4 (R22)	1	3043-106
325-3	Orifice for oil injection - dia. 2 (HFC)	1	3043-142
	Electrical signal transmitter for
	capacity slide position (optional)
350	Turning transmitter	1	3448-004
351-1	Sight-glass for transmitter (L)	1	3045-010
351-2	Sight glass for transmitter (S)	1	3045-011
352	Screw for transmitter M3 x 8 (incl. in pos. 350)	(4)	1412-012
0661-845

Pos.	Designation	No.	Part no
	Oil filter
450	Flange	1	3013-176
451	O-ring dia. 66,27 x 3,53	1	1331-072
452	O-ring dia. 107,54 x 3,53	1	1331-085
455	Cylinder screw M5 x 16	2	1413-331
456	Guide ring dia. 14,5/6	3	2356-120
457	Washers dia. 18/6	3	2356-122
458	Rod for magnets	1	3042-043
459	Magnet	4	1517-022
460	Spacer for magnet	3	3424-039
461	Spring	1	2143-026
462	Spring	1	2143-063
470	Oil filter cartridge	1	1517-040
480	Welding flange	1	3013-175
481	O-ring dia. 91,67 x 3,53	1	1331-080
	Oil flow switch
500	Terminal box	1	1554-001
501	Housing for flow switch	1	3013-076
502	O-ringdia.107.54 x 3.53	1	1331-085
503	Guide for oil filter	1	3042-047
504	Circlip	1	1437-168
505	Nippel for flow switch	1	2314-106
506	Gasket dia. 32/27 x 1,5	1	2356-139
507	Flow switch with ball	1	1553-024
509	Gasket dia. 20/13 x 1,5	1	2356-125
510	Spring	1	2144-041
511	Washer dia. 22/13 x 2,0	1	2114-046
512	Cylinder screw M 12 x 35	4	1413-387
	Safety valve
550	Safety valve	1	3042-046
551	Bush	1	3042-036
552	O-ring dia. 91,67 x 3,53	1	1331-080
553	O-ring dia. 91,67 x 3,53	1	1331-080
554	Cylinder screw M6 x 25	4	1413-342
555	O-ring dia. 56,74 x 3,53	1	1331-069
556	Welding flange	1	3013-077
557	Cylinder screw	4	1413-403
0661-845

Pos.	Designation	No.	Part no
	Limitation of minimum capacity (optional)
	Please refer to the instruction manual, section 9
228	Spacer ring for SAB 110 S and L	1	3045-041
229	O-ring dia. 69,52 x 2,62	1	1331-145
210-2	Spindle, replaces pos. 210-1	1	3045-063
75-3	Glass for indicator SAB 110 L, replaces pos. 75-1	1	304S-043
75-4	Glass for indicator SAB 110 S, replaces pos. 75-2	1	304S-042
351-3	Glass for indicator for turning transmitter SAB 110 L,	1	3045-045
	replaces pos. 351-1
351-4	Glass for indicator for turning transmitter SAB 110 S,	1	3045-044
	replaces pos. 351-2
	Temperature/pressure transducers
751	Pressure transducer, suction gas (PT1)	1	1373-249
752	Pressure transducer, oil after filter (PT3)	1	1373-271
753	Pressure transducer, oil before filter (PT4)	1	1373-271
756	Elbow coupling 10-RL	3	1349-154
761	Temperature transmitter, compressor oil (TT6)	1	1373-264
762	Temperature transmitter, suction gas (TT7)	1	1373-264
765	Gasket ring DKA R 1/4"	2	1349-135
0661-645

List of parts for SAB 128 Mk3

List of parts for SAB 128 Mk3

Relevant drawing 0661-874
Unless otherwise stated all measurements are given in mm.

Pos.	Designation	No	Part no.
	Complete compressor for male drive		4161-074
	Complete compressor for female drive		4161-073
	Compressor housing
10	Rotor housing	1	3011-021
	Bearing cover at suction end
20	Bearing cover	1	3013-143
21	O-ring dia 304.39 x 3.53	1	1331-112
22	Cylindrical pin dia 12 x 40	2	1445-084
23	Socket cap screw M12 x 35	16	1413-387
24	Threaded plug with collar 1/2"	1	1343-027
25	Gasket dia 27/21 x 1,5	1	2356-133
	Bearing cover at discharge end
40	Cover	1	3013-052
43	Cylinder screw M10 x 35	6	1413-373
44	Adjusting screw	2	2111-122
45	Locking screw M6x 10	4	1413-231
	Capacity regulating cylinder
50	Cylinder	1	3043-010
51	O-ring dia 82.14x3.53	1	1331-077
52	Cylinder screw M10 x 35	3	1413-373
	Cover for capacity regulating cylinder
60	Cover	1	3013-193
61	O-ring dia 88.49 x 3.53	1	1331-079
62	Cylinder screw M8 x 25	4	1413-357
	Housing for capacity indicator
70	Housing	1	3045-002
71	Cylinder screw M6 x 30	4	1413-343
72	Cover for capacity indicator	1	3045-003
73	Cylinder screw M6 x 50	4	1413-347
74	O-ring dia 98.02 x 3.53	1	1331-081
75.1	Glass for indicator	1	3045-006
	Shaft seal cover
80	Shaft seat cover	1	3013-051
81	O-ring dia 85.32 x 3.53	1	1331-078
82	Cylinder screw M10 x 35	4	1413-373
83	Driving pin dia 4 x 8	1	1446-011
86	Hose connection 1/4"	1	1343-025
87	Plastic hose 3/16"	1	1241-190
88	Plug 1/4"	1	1345-025
89	Gasket dia. 19/14 x 1.5	1	2356-124
	Cap cover
90	Cap cover	1	3013-050
91	O-ring dia 85.32 x 3.53	1	1331-078
92	Cylinder screw M10 x 35	4	1413-373
	Cover for slide stop
100	Cover	1	3013-057
101	O-ring dia 66.27 x 3.53	1	1331-072
102	Cylinder screw M10 x 35	3	1413-373
103	Retainer for spindle bearings	1	3044-013
104	Cylinder screw M6 x 20	4	1413-341
105	Locking plate	1	2114-043
	Rotors and suction end bearings
110	Set of rotors for SAB 128H, female drive	1(F)	3024-018
110	Set of rotors for SAB 128 H, male drive	1(M)	3024-109
111	Roller bearing	2	1513-016
112	Retainer pin for male rotor	1	3021-012
113	Oil splash ring	1	1437-217
114	Thrust washer	2	3021-035
115	Cylinder screw M12 x 35	2	1413-387
118	Driving pin dia 4 x 8	1	1446-019
119	Retainer pin for female rotor	1	3021-017
120	Balance piston, suction end	1	3025-007
	Discharge end bearings, female rotor
130	Balance piston dia. 64	1	3025-016
131	Radial roller bearing dia. 40/90 x 33	1	1513-016
132	Four point bearing dia. 40/90 x 23	1	1513-027
133	Set of shims dia- 70/90 for adjusting the	1	2124-080
	clearance between the rotor and outlet port
	comprising: 1 off thickness 0.49mm
	1 - 0.52mm
	1 - 0.55 mm
	1 - 0.58 mm
	1 - 0.61 mm
	1 - 0.64mm
	1 - 0.67mm
	Discharge end bearings, male rotor
135	Balance piston dia 64	1	3025-016
136	Radial roller bearing dia 45/100 x 36	1	1513-012
137	Four point bearing dia 45/100 x 25	1	1513-028
138	Set of shims dia 80/100 for adjusting the	1	2124-081
	clearance between the rotor and outlet port
	comprising: 1off thickness 0.49mm
	1 - 0.52mm
	1 - 0.55 mm
	1 - 0.58 mm
	1 - 0.61 mm
	1 - 0.64mm
	1 - 0.67mm
	Discharge ports
140	Discharge port for male rotor	1	3031-037
141	Discharge port for female rotor	1	3031-038
142	Socket cap screw M8 x 120	6	1413-314
143	Sealing ring dia 13/8	6	3049-006
144	Set screw M 10x20	2	1413-252
145	Set screw M1 Ox 10	2	1413-253
146	Blank off screw	2	1343-027
147	Locking screw M 10 x 10	2	1413-253
148	Adjusting screw M10 x 20	2	1413-032
149	Gasket	2	1331-427
	Parts for adjusting rotors
151	Thrust cover for male rotor	1	3013-053
152	O-ring dia 91.67 x 3.53	1	1331-080
153	Thrust cover for female rotor	1	3013-054
154	O-ring dia 82.14 x 3.53	1	1331-077
	Shaft seal
160	Shaft seal type 680.	1	1332-161
	Suction filter
170	Suction filter	1	3042-081
171	Set screw M6 x 10	3	1413-231
	Adjusting system for V_i-slide
180	Spindle	1	3044-012
182	Spacer ring	1	3044-014
183	Sealing ring dia 28/22	1	1331-503
184	O-ring dia 44.04 x 3.53	1	1331-065
186	Spindle bearing	2	1512-015
	Slide stop
190	Slide stop (included in pos. 192)
	Man. Vi-slide
191	Spring	1	1523-014
192	Slide control (including slide stop, pos. 190)	1	3044-071
193	Socket cap screw M10 x 25	1	1413-371
	Capacity regulating slide
200	Slide	1	3043-175
201	Inner piston part	1	3043-075
202	Outer piston part	1	3043-076
203	O-ring dia 53.57 x 3.53	1	1331-068
204	Sealing ring dia 90/80	1	1332-118
205	Cylindrical pin dia 6 x 12 (incl. in pos no 207)	(1)	1445-075
206	Cylinder screw M6 x 25	4	1413-342
207	Piston rod	1	3043-112
208	Tape bearing	2	2132-105
209	O-ring dia 9,12 x 3,53	1	1331-215
	Spindle for capacity indication
210.1	Spindle	1	3045-057
216	Magnetic coupling	1	3045-061
217	O-ring dia. 44,12 x 2,62 (incl. in pos. 216)	(1)	1331-146
218	Hexagon head screw M4 x 16 (incl. in pos. 216)	(1)	1413-320
219	Hexagon head screw M4 x 20 (incl. in pos. 216)	(2)	1413-322
	Capacity indication
221	Indicator dial	1	3045-001
223	Cylinder screw M4 x 10	1	1413-319
224	Supporting ring	1	2356-155
226	Locking washer DC 15/8,4	1	1437-054
227	Locking washer DC 8/4.3	1	1437-060
	Suction gas inlet
252	O-ring dia 190.09 x 3.53	1	1331-105
253	Inlet flange	1	3013-130
254	Cylinder screw M16 x 45	8	1413-433
257	Plug 1/4"	1	1343-025
258	Gasket ring dia. 21/14 x 2,0	1	1331-428
259	O-ring dia. 20,22 x 3,53	1	1331-019
	Non-return (check) valve
260	Valve cone	1	3042-107
261	Spring	1	1523-033
262	Cylinder screw M10 x 25	1	1413-371
263	Adaptor	1	3042-079
264	Tape bearing dim 10x1 x 136	2	2132-099
265	Locking device for non-retun valve	1	3042-108
266	Pointed screw M6 x 6	1	1413-229
	Suction side connection
279	Flange	1	3013-130
280	Cylinder screw M16 x 45	8	1413-433
281	O-ring dia 190.09 x 3.53	1	1331-105
	Economizer inlet
290	Flange with plug	1	3013-135
291	Cylinder screw M10 x 30	2	1413-372
292	O-ring dia 29.74 x 3.53	1	1331-025
	HLI Inlet
300	Flange with plug	2	3013-136
301	Cylinder screw M10 x 30	4	1413-372
302	O-ring dia 20.22 x 3.53	2	1331-019
	Connecting parts for slide rod
310	Washer for slide rod	1	3043-108
311	Cylinder screw M10 x 55	1	1413-377
	External oil piping
320-1	Pipe set complete, female drive	1	3049-021
320-2	Pipe set complete, male drive	1	3049-031
325-1	Orifice dia. 5,0 for oil injection pipe - R717	1	3142-052
325-2	Orifice dia. 3,2 for oil injection pipe - R22 and HFC's	1	3142-054
331	Plug 1/2"	1	1343-027
332	Gasket ring dia. 28,5/21.6 x 2,3	1	1331-430
333	Plug 1/4"	1	1343-025
334	Gasket ring dia. 24/14 x 2,0	1	1331-428
335	Plug 1/4"	1	1343-025
336	Gasket ring dia. 21/14x2,0	1	1331-428
337	Plug 3/4"	1	1343-028
338	Gasket dia. 34,93/27.13 x 2,34	1	1331-433
	Electrical signal transmitter for
	capacity slide position (optional)
350	Turning transmitter	1	3448-004
351.1	Sight-glass for transmitter	1	3045-007
352	Screw for transmitter	4	1412-012
	M3 x 8(included in pos. 350)
	Limitation of minimum capacity (optional)
228	Spacer ring for SAB 128H	1	3045-028
229	O-ring dia. 82.14x3.53	1	1331-077
210.2	Spindle
	replaces pos. 210.1	1	3045-063
	Limitation of minimum capacity (optional)
75.2	Glass for indicator, SAB 128/163
	replaces pos. 75.1	1	3045-036
351.2	Glass for indicator for turning transmitter, SAB 128/163 replaces pos. 351.1	1	3045-037
	Oil filter parts
450	Cover	1	3041-008
452	O-ring dia 132,94 x 3,53	1	1331-093
453	O-ring dia 101,19 x 3.53	1	1331-083
455	Locking nut M10	1	1433-080
456	Cylinder screw	4	1413-387
458	Stay bolt	1	2111-129
459	Magnet	4	1517-022
460	Intermediate ring	4	3424-039
461	Elastomer ring	2	1334-012
470	Filter element	1	1517-121
471	Plug 1/4"	1	1343-025
472	Gasket ring dia. 21/14 x 2,0	1	1331-428
473	O-ring dia. 20,22 x 3,53	1	1331-019
480	Filter housing	1	3042-084
481	O-ring dia 183,74 x 3,53	1	1331-104
482	Cylinder screw M8 x 25	4	1413-357
483	Pointed screw M6 x 8	3	1413-230
	Flow switch arrangement
500	Terminal box	1	1554.001
505	Nippel	1	2314-106
506	Dowty ring 34,9/27,1 x 2,3	1	1331-433
507	Flow switch with ball	1	1553-024
508	Washer	1	2114-046
509	Gasket ring 19/14 x 1,5	1	2356-124
510	Spring	1	2144-041
511	Circlip (part of pos. 507)	1
	Compressor relief valve system
700-1	Back pressure independent safety valve,	1	2416-202
	BSV8, 18 bar
700-2	Back pressure independent safety valve,	1	2416-203
	BSV8, 20 bar
700-3	Back pressure independent safety valve,	1	2416-204
	BSV8. 21 bar
700-4	Back pressure independent safety valve,	1	2416-224
	BSV8, 22 bar
700-5	Back pressure independent safety valve,	1	2416-205
	BSV8, 25 bar
701	Connection line, POV 40, dia. 12	1	3014-013
702	Cylinder screw M12 x 35	4	1413-387
703	O-ring dia. 82,14x3,53	1	1331-077
704	Main valve POV 40 including connection pipe	1	3014-011
715	Cover	1	3013-180
716	Cylinder screw M14 x 90	4	1413-417
717	O-ring dia. 69,44 x 3,53	1	1331-073
721	Cylinder screw M12 x 30	4	1413-386
722	O-ring dia. 63,09 x 3.53	1	1331-071
725	Banjo coupling	1	1349-091
726	Al gasket, dia, 24/13 x 1,5	1	2356-127
727	Reducer G 3/4-G 3/8"	1	2312-038
730	Union nut G 1"-3/8"	1	2469-070
732	Al gasket, dia- 30/16 x 1,5	1	2356-137
	Temperature/pressure transducers
751	Pressure transducer, suction gas (PT1)	1	1373-249
752	Pressure transducer, oil after filter (PT3)	1	1373-271
753	Pressure transducer, oil before filter (PT4)	1	1373-271
755	Coupfing 10-RL	2	1349-137
756	Elbow coupling 10-RL	1	1349-154
761	Temperature transmitter, compressor oil (TT6)	1	1373-281
762	Temperature transmitter, suction gas (TT7)	1	1373-282
765	Gasket ring - DKA R 1/4	2	1349-135

Spare parts survey for SAB 128 Mk3 unit

The following list comprises all components that can be fitted

on a compressor unit.

From this list we have selected the components that are used

on a particular unit and which are indicated on the piping

diagram of this instruction manual. The position numbers on the

piping diagram are a reference to the "Pos." columns of this list.

The piping diagram is dedicated to the compressor number

stated on page 1 of this instruction manual.

The components in the shaded areas are variable. This may be

due to voltage, refrigerant, approved pressure etc.

On ordering spare parts it may be an advantage to receive them in

sets selected for your specific compressor unit.

A list of sets can had on request from SABROE's local

representative.

Regulating & Control delice	Pos.	Designation	Part no.
		UNISAB II
	PT1	Pressure transducer -1-9 bar	1373-249
	PT2	Pressure transducer -1 - 25 bar	1373-250
	PT3	See PT2
	PT4	See PT2
	TT5/6/7	Temperature transducer PT100	1373-264
	GT8	Position transmitter (capacity)	3448-004
	GT9	See GT8
		UNISAB II Frontpanel	1573-007
		1 CPU-module	1572-017
		1 Relay print	1574-014
		1 EPROM extractor	1613-002
		1 EEPROM extractor	1613-003
		1 EEPROM	1571-015

		3 Jumpers
		2 Fuses	1572-018
		1 Screw driver
Refrigerant system		Suction:
	20	O-ring dia 132,94 x 3,53	1331-093
		Set of gaskets for SCV80 (R717)	3184-078
		Set of gaskets for SCV100 (R22)	3184-079
	24
	34-35	Set of gaskets for SNV 8	2453-053
	47-48
		Oil separator, general:
	30	Sealing ring dia. 42/49 x 6,5	1349-213
	30	Heating rod, 250 V	3181-038
		Heating rod. 115V	3181-039
		Heating rod, 230	3181-040

	31	O-ring dia 52.07 x 2.62 (sight glass)	1331-140
		Sight glass	1226-017

	55	O-ring dia 329,57 x 5,33 (for cover)	1331-184
		Oil seperating element	1517-062

		Oil return:
	52	Nozzle valve	1364-151
	53	Sight glass	1226-014
	53	Gasket dia. 40.5/33 x 1.5	2356-144

		Discharge:
	204	Set of gaskets for SCV65	3184-078
		O-ring dia 78,97 x 3,53	1331-076

	22	Safety valves:
	28	DN 25/40
		Gasket, dia. 57/43 x 2	2356-260
		Gasket, dia. 75/61 x 2	2356-220
		O-ring dia. 61,60 x 2,62 (house)	1331-143
		Conical seal for DN 25/40	1365-077
		Spring (for 25 Bar opening pressure)	1365-046

	28	DN 40/65
		Gasket, dia. 75/61 x 2	2356-220
		Gasket, dia. 109/95 x 2	2356-222
		O-ring dia. 91,94 x 3,53	1331-080
		Conical seal for DN 43,65	1365-079
		Spring (for 25 Bar opening pressure)	1523-027

Oil system		Flange connection, oil tube
		Gasket, dia 57/43 x 2	2356-260
		O-ring dia 59,92 x 3,53 (compr.)	1331-071

		Oil by-pass (at pump)
	210	Gasket, dia 102/55 x 1,5 (non-return valve)	2356-092
		O-ring dia 26.57 x 3,53 (non-return valve)	1331-023

	69	Pressure build up for capacity reg.
		Non-return valve 18, 1 bar	1364-004
		Non-return valve 10, 02 bar	1364-008

		Oil pump
	63	Shaft seal complete	1332-192
	63	O-ring dia 44,12 x 2,62 (cover for pump)	1331-146
	64-65	Set of gaskets for SVA 15	2453-022
	60-62	Set of gaskets for SVA 32
	61	Filter element 150	2464-233
	61	O-ring dia 44,04 x 3,53	1331-022
	61	O-ring dia 36,09 x 3,53	1331-018
	61	O-ring dia 13.94 x 2,62	1331-014

Capacity regulation	46	Thermostatic three-way valve, type RT3
		O-ring, Neoprene	1331-383
		Thermo element, 48°C	1365-005

	70	Solenoid valve block
		Valve housing EVM (NC)	1372-335
		Gasket set for EVM (NC/NO)	1336-024
		Coil 10W 220V 50/60 Hz	1372-330
		110V 50/60 Hz	1372-331
		250V 50/60 Hz	1372-334

	71	Solenoid valve:
		Valve housing EVM (NO)	1372-425
		Gasket set for EVM	1336-024
		Throttle valve
	72	Gasket set 6F	1377-210
	73	Solenoid valve:
		See pos. 70
	74	Solenoid valve:

BLI Oil cooling	80-84	Gasket set for SVA 15-20	2453-022

	81	Filter FA15:
		(When TEAT 20 is selected)
		Gasket set for FA15	1377-078
		Repair kit for FA15	1377-250

	81	Filter FA20:
		(When TEAT 85 is selected)

		Gasket set for FA20	1377-079
		Repair kit for FA20	1377-251

	82	Solenoid valve EVRA15
		(when TEAT 20 is selected)

		Gasket set (for EVRA15)	1377-093
		Repair kit (for EVRA15)	1377-099
		Coil 10W 220V 50/60 Hz
		110V 50/60 Hz See pos 70
		250 V 50/60 Hz
	82	Solenoid valve EVRA20
		(when TEAT 85 is selected)

		Gasket set (for EVRA 20)	1377-094
		Repair kit (for EVRA20)	1377-069
		Coil 10W 220V 50/60 Hz
		110V 50/60 Hz See pos 70
		250 V 50/60 Hz

	83	Injection valve TEAT 82
		Nozzle insert 20-5	1371-202
		Nozzle insert 20-8	1371-203
		Nozzle insert 20-12	1371-204
		Nozzle insert 21-20	1371-206
		Thermal part 351B5 deg.C	1371-255
		Thermal part 55-95 deg.C	1371-253

	83	Injection valve TEAT 85
		Nozzle insert 85-33	1371-207
		Nozzle insert 85-55	1371-208
		Nozzle insert 85-85	1371-209
		Thermal part 35-65 deg. C	1371-257
		Thermal part 55-95 deg.C	1371-250

Compr.con- nections		Spare parts set for coupling S952 size 225
		Sheets, bolts, nuts & slices	1524-124
		Spacer bushing	1526-002
		Stop screw M10 x 10	1413-250
		Combination wrench 1/2"	Compr.
		Box wrench 1/2"	Tools

		Alignment motor - compressor
		Discs (motor up to IEC 280)	2221-067
		Discs (motor from IEC 315)	2221-076
		Tools	3183-104

Line no A401 = Normal set (part no. 3083-044)
Line no. A402 = Extended set (part no. 3083-046)
Line no. B401 = Tools for coupling alignment (part no 3183-104)
Line no. B40 = Tools for shaft seal removal, oil pump (part no 3083-160)

Tool no.	Designation	Part no.	A401	A402	B401	B402
1	Puller for bearings	3083-060	1	1
2	Thrust ring for the puller, female	3083-043	1	1
3	Thrust ring for the puller, male	3083-127	1	1
4	Tool for fitting the bearings	3083-062	1	1
5	Ring for the puller	3083-042	1	1
6	Tool for pressing out the rotors	3083-063	1	1
7	Tool for fitting the bearings	3083-061	1	1
8.1	Retaining cup for male rotor	3083-097	1	1
8.2	Retaining cup for female rotor	3083-098	1	1
9	Tool for dismounting the bearings	3083-041	2	2
10	Thrust washer	3083-002	1	1
11	Locking tool for rotor	3083-126	1	1
20.1	Threaded pin M10 x 160	2112-129	4	4
20.2	Threaded pin M12 x 275	2112-148	1	1
21.1	Hexagon head screw M16 x 130	1424-271	1	1
21.2	Hexagon head screw M10 x 130	1424-203	4	4
22.2	Socket cap screw M8 x 35	1413-359	1	1
22.3	Socket cap screw M8 x 120	1413-314	2	2
22.4	Socket cap screw M10 x 25	1413-371	4	4
22.6	Socket cap screw M12 x 35	1413-387	1	1
22.7	Socket cap screw M12 x 90	1413-400	1	1
23.1	Nuts M8 Nuts M12	1432-063	2	2
23.2	Nuts M10	1432-064	4	4
23.3	Nuts M12	1432-065	1	1
24.1	Washer dia. 24/13 x 2.5	1436-036	1	1
24.2	Washer dia. 35/13 x 5	1436-140	3	3
25	Guide pin M16 x 300	2112-147	2	2
30	Tool for adjusting the bearings	3083-096	1	1
31	Special screw for adjusting the bearings	3083-095	1	1
32.1	Eye bolt M12	1427-150	1	1
32.2	Eye bolt M16	1427-156	1	1
33	Alignment device for coupling	3183-104			1
34	Feeler gauge	1622-050			1
36	Tools for shaft seal removal, oil pump Consist of:
36.1	Pullef for shaft seal, oil pump	3083-157				1
36.2	Cap screw M10 x 75	1424-201				1
36.3	Threaded pin M8 x 150	3083-156				3
36.4	Nut M8	1432-063				3
36.5	Punch dia. 18 x 60	3063-158				1
36.6	Punch dia. 22/16,5 x 100	3083-159				1
40.1	Torque wrench(Ratchet) 5 - 50 Nm 1/2"			1
40.2	Torque wrench 40-200 Nm (14 x 18)			1
42	Extension 1/2"			1
43	Converter for torque wench(14x18) - 1/2"			1
44.1	Hexagon bit adapter 1/2" - 4mm			1
44.2	Hexagon bil adapter 1/2" - 5mm			1
44.3	Hexagon bit adapter 1/2"- 6mm			1
44.4	Hexagon bit adapter 1/2" - 8mm			1
44,5	Hexagon bit adapter 1/2" - 10mm			1
44.6	Hexagon bit adapter 1/2" - 14mm			1
45	Box spanner insert 1/2" - 19mm			1
45.1	Box spanner insert 1/2" - 24mm			1
45.2	Box spanner insert 1/2" - 27mm			1
45.3	Box spanner insert 1/2" -36mm			1
45.4	Box spanner insert 1/2" -1/2"			1
46	Open end spanner (14x18) - 19mm			1
50.1	Combination spanner 17mm	1613-276		1
50.2	Combination spanrer 19mm	1612-277		1
50.3	Conbination spanner 1/2"
51.1	Allen key for socket cap screw 3mm	1512-395		1
51.2	Allen key for socket cap screw 5mm	1612-397		1
51.3	Allen key for socket cap screw 6mm	1612-398		1
51.4	Allen key for socket cap screw 8mm	1612-399		1
51.5	Allen key for socket cap screw 10mm	1612-401		1
51.6	Allen key for socket cap screw 14mm	1612-400		1
52	Magnetic Fixture for dial indicator			1
53	Dial indicator			1
54.1	Retaining ring pliers			1
54,2	Retaining ring pliers			1
55.1	Hammer	1612-012		1
55.2	Plastic hammer	1612-042		.1
56	Steel punch 8 mm			1
57	Pliers for driving pin	1612-190		1

List of parts for SAB 163 Mk3

List of parts for SAB 163 Mk3

Relevant drawing: 06G1-884
Unless otherwise stated all measurements ara givan in mm.

Pos.	Designation	Quantity		Part no.
		Aut.Vi	Man.Vi
	Complete compressor, female drive, Man.Vi		1(F)	4161-069
	Complete compressor, female drive, Aut. V,	1(F)		4161-070
	Complete compressor, male driva, Man. Vi		1(M)	4161-071
	Complete compressor, male driva, Aut.Vi	1(M)		4161-073
	Compressor housing
10	Rotor housing, SAB -163H	1	1	3011-020
	Bearmg cover at suction end
20	Suction cover for SAB 163 M	1	1	3013-141
21	O-ring 380.37 x 5.33	1	1	1331-187
22	Cylindrical pin dia. 16 x 50	2	2	1445-091
23	Cylinder screw M16 x 45	16	16	1413-433
24	Plug with collar 1/2"	1	1	1343-027
25	Aluminium gasket dia. 27/21 x 1,5	1	1	2356-133
	Bearing cover at discharge end
40	Cover for bearings	1	1	3013-017
43	Cylinder screw M10 x 35	6	6	1413-373
44	Adjusting screw M20	2	2	2111-122
45	Locking screw M6 x 10	4	4	1413-231
	Capacity regulating cylinder
50	Capacity cylinder	1	1	3043-009
51	O-rlng 107.54 x 3.53	1	1	1331-085
52	Cylinder screw M12 x 40	3	3	1413-358
	Cover for capacity regulating cylinder
60	Cover for capacity cylinder	1	1	3013-194
61	O-ring 120.24 x 3.53	1	1	1331-089
62	Cylinder screw M12 x 30	4	4	1413-386
	Housing for capacity indicator
70	Capacity indicator housing	1	1	3045-002
71	Cylinder screw M6 x 30	4	4	1413-343
72	Capacity indicator cover	1	1	3045-003
73	Cylinder screw M6 x 50	4	4	1413-347
74	O-ring 98.02 x 3.53	1	1	1331-081
75.1	Sight glass for capacity indicator	1	1	3045-006
	Shaft seal cover
80-1	Shaft seal cover, before jure 1998	1	1	3013-142
80-2	Shaft seal cover, before jure 1998	1	1	3013-209
81	O-ring 113.89 x 3,53	1	1	1331-087
82-1	Cylinder screw M12 x 50, before june 1998	1	1	1413-390
82-2	Cylinder screw M12 x 35, before june 1999	2	2	1413-367
82-3	Cylrnder screw M12 x 35, after june 1998	4	4	1413-387
83	Driving pin dia. 4 x 6	1	1	1446-011
84	Plug with rim 1/4"	1	1	1343-025
85	Gasket dia. 19/14 x 1,5	1	1	2356-124
86	Hose connecting branch '1/4"	1	1	1345-143
87	Clear plastic hose 3/16" x 300 mm	1	1	1241-190
88	Plug with rim 3/8", before june 1998	1	1	1343-026
89	Dowty ring dia 23,8/17,35 x 2, before june 1998	1	1	1331-427
	Cap cover
90	Cap cover	1	1	3013-036
91	O-ring 113.89 x 3.53	1	1	1331-087
92	Cylinder screw M12 x 35	3	3	1413-387
	Cover for slide stop
100	Slide stop cover		1	3013-068
101	O-ring 78,97 x 3.53		1	1331-076
102	Cylinder screw M12 x 35		4	1413-387
103	Bearing retainer		1	3021-018
104	Cylinder screw M6 x 20		4	1413-341
105	Locking plate		1	2114-043
	Rotors and suction end bearings
110	Rotor set for SAB 163 H, female drive	1(F)	1(F)	3024-006
110	Rotor set for SAB 1631H, male drive	1(M)	1(M)	3024-106
111	Radial roller bearing	2	2	1513-017
113	Oil splash ring external dia. 46	1	1	1437-287
114	Washer for bearing	2	2	3021-007
115	Cylinder screw M16 x 45	2	2	1413-433
118	Driving pin dia. 4.0 x 10	1	1	1446-012
119	Retainer pin	2	2	3021-009
120	Balance piston, suction end	1	1	3025-008
	Discharge end bearings, female rotor
130	Balance piston dia. 86	1	1	3025-037
131	Radial roller bearing dia. 55/120 x 43	1	1	1513-017
132	Four point bearing dia 55/120 x 29	1	1	1513-029
133	Set of shims dia. 100/120, for adjusting the
	clearance between the rotors and outlet ports,	1	1	2124-082
	Comprising; 1 off thickness 0.49 mm
	1 off - 0.52 mm
	1 off - 0.55 mm
	1 off - 0.56 mm
	1 off - 0.61 mm
	1 off - 0.64 mm
	1 off - 0.67 mm
	Discharge end bearings, mate rotor
135	Balance piston dia. 86	1	1	3025-037
136	Radial roller bearing dia.60/130 x 46	1	1	1513-013
137	Four point bearing dia.60/130 x 31	1	1	1513-030
138	Set of shims dia. 105/130 for adjustnig the.
	clearance between, the rotors and outlet ports,	1	1	2124-083
	Comprising 1off thickness 0.49 mm
	1 off - 0.52 mm
	1 off - 0.55 mm
	1 off - 0.58mm
	1 off - 0.61 mm
	1 off - 0.64 mm
	1off - 0.67 mm
	Discharge end ports
140	Outlet port (male rotor)	1	1	3031-035
141	Outlet port (femle rotor)	1	1	3031-036
142	Cylinder screw M10 x 150	6	6	1413-376
143	Steel gasket dia. 16/10 x 2	6	6	2351-030
144	Set screw M10 x 20 (first production series)	2	2	1413-252
145	Set screw M10 x 10 (first production series)	2	2	1413-250
146	Blank-off screw	2	2	1343-026
147	Locking screw M 10 x 10 (new productian series)	2	2	1413-253
148	Adjusting screw M10 x 20 (new productian series)	2	2	1413-032
149	Gasket	2	2	1331-427
	Parts for adjusting rotors
151	Inner cover (male rotor)	1	1	3013-019
152	O-ring 123.42 x 3.53	1	1	1331-090
153	Inner cover (female rotor)	1	1	3013-045
154	O-ring 113.89 x 3.53	1	1	1331-087
	Shaft seal
160	Shaft seal type 680	1	1	3084-529
	Suction filter
170	Suction filter	1	1	3042-081
171	Set screw M6x 10	3	3	1413-231
	Adjusting system for V_i-slide
180	Spindle for slide stop		1	3044-012
182	Sealing washer for slide stop		1	3044-014
183	Sealing ring dia 28/22		1	1331-503
184	O-ring 44.04 x 3.53		1	1331-065
186	Axial ball bearing dia. 42/25 x 11		2	1512-015
	Slide stop
190	Slide stop (included in pos.192 and pos. 370)
	Man. V_i- slide
191	Spring	1	1	1523-162
192	Slide control (including slide stop, pos. 190)		1	3044-066
193	Cylinder screw M10 x 12	1	1	1413-408
	Capacity regulating slide
200	Capacity slide	1	1	3043-174
201	Inner piston slide	1	1	3043-092
202	Outer piston slide	1	1	3043-093
203	O-ring 53.57 x 3.53	1	1	1331-068
204	Gasket	1	1	1332-107
205	Cylindrical pin dia. 6 x 12 (included in pos no 207)	(1)	(1)	1445-075
206	Cylinder screw M6 x 25	4	4	1413-342
207	Slide rod	1	1	3043-111
208	Tape bearing	2	2	2132-104
209	O-ring 21.62 x 3.53	1	1	1331-020
	Spindle for capacity regulation
210.1	Spindle for capacity indicator	1	1	3045-058
216	Magnetic coupling	1	1	3045-061
217	O-ring dia 44,12 x 2,62 (incl.in pos.216)	(1)	(1)	1331-146
218	Hexagon head screw M4 x 16 (inci. in pos. 216)	(1)	(1)	1413-320
219	Hexagon head screw M4 x 20 (incl. in pos. 216)	(2)	(2)	1413-322
	Capacity indication
221	Indicator dial	1	1	3045-001
233	Cylinder screw M4 x 10	1	1	1413-319
224	Supporting ring	1	1	2356-155
226	Locking washer DC 15/8,4	1	1	1437-054
227	Locking washer DC 8/4,3	1	1	1437-060
	Suction gas inlet
252	O-ring dia.190.09 x 3.53	1	1	1331-105
253	Inlet flange	1	1	3013-130
254	Cylinder screw M 16 x 45	8	8	1413-433
257	Plug 1/4"	1	1	1343-025
258	Gaskel ring dia. 21/14 x 2,0	1	1	1331-428
259	O-ring dia. 20,22 x 3,53	1	1	1331-019
	Non-return valve
260	Valve cone	1	1	3042-107
261	Spring	1	1	1523-033
262	Cylinder screw M10 x 25	1	1	1413-371
263	Adaptor	1	1	3042-079
264	Tape bearing dim 10 x 1 x 136	2	2	2132-125
265	Locking device	1	1	3042-108
266	Pointed screw M6 x 6	1	1	1413-229
	Suction side connection
279	Flange	1	1	3013-130
280	Cylinder screw M 16 x 45	8	8	1413-433
281	O-ring 190.09 x 3.53	1	1	1331-105
	Economizer inlet
290	ECO plug	1	1	3013-128
291	Cylinder screw M10 x 30	1	1	1413-372
292	O-ring 37.69 x 3.53	1	1	1331-030
293	Cylinder screw M8 x 25	1	1	1413-357
	HLI inlet
300	HLI plug	2	2	3013-127
301	Cylinder screw M10 x 30	4	4	1413-372
302	O-ring 23.39 x 3,53	2	2	1331-022
	Connecting parts for slide rod
310	Washer for slide rod	1	1	3043-109
310	Cylinder screw M10 x 65	1	1	1413-383
	Internal oil piping
320-1	Pipe set complete, female drive, before june 1998	1	1	3049-045
320-2	Pipe set complete, male drive, before june 1998	1	1	3049-030
320-3	Pipe set complete, female drive, after june 1998	1	1	3049-045
320-4	Pips set complete, male drive, after june 1998	1	1	3049-046
325.1	Orifice dia. 7 for oil injection pipe - R717	1	1	3142-062
325.2	Orifice dia. 5 for oil injection pipe - R22 and HFC's	1	1	3142-052
331	Plug 1/3"	1	1	1343-027
332	Gasket ring dia. 28,5/21,6 x 2,3	1	1	1331-430
333	Plug 1/4"	1	1	1343-025
334	Gasket ring dia. 21/14 x 2,0	1	1	1331-428
335	Plug 1/4"	1	1	1343-025
336	Gasket ring dia. 21/14 x 2,0	1	1	1331-428
337	Plug 3/4"	1	1	1343-028
338	Gasket ring dia 34,93/27,13 x 2,34	1	1	1331-433
	Electrical signal transmitter for
	capacity slide positon (optional)
350	Turning transmitter	1	1	3448-004
351.1	Sight glass for transmitter	1	1	3045-007
352	Screw for transmitter M3 x 8 (inducted in pos. 350)	4	4	1412-012
	Limitation of minimum capacity (optional)
228	Spacer ring for SAB 163H	1	1	3045-029
229	O-ring dia. 113.89 x 3.53	1	1	1331-087
210.2	Spindle
	(replaces pos. 210.1)	1	1	3045-064
75.2	Glass for indicator, SAB 128/163
	(replaces pos. 75.1)	1	1	3045-036
351.2	Giass for indicator, SAB 128/163 for turning transmitter
	(replaces pos. 351.1)	1	1	3045-037
	Aut. V_i slide
370	Slide control for auto. V_i
	(including slide stop pos.190)	1		3044-065
371	Gasket dia. 72	1		1333-119
372	Piston for Auto. V_i	1		3044-042
373	Cylindrical pin dia. 6 x 12
	(included in pos. 372)			1445-075
374	Cylinder screw M6 x 12	4		1413-339
	Cover for slide stop
380	Slide stop cover for auto. V_i	1		3013-195
381	O-ring 78.97 x 3.53	1		1331-076
382	Cylinder screw M12 x 30	4		1413-386
383	Cylindrical pin dia 8 x 24	1		1445-077
	Spindle for V\| indication
390	Spindle for auto. V_i	1		3044-062
395	Driving disc	1		3044-021
396	Cylinder screw M 4x 12	1		1413-318
	Bearing retainer Tor Aut. V_i
400	Bearing retainer tor aut. V_i	1		3044-064
401	Cylinder screw M6 x 45	4		1413-307
402	Cover for the transmitter	1		3045-009
403	Cylinder screw M4 x 10	4		1413-319
405	Magnetic coupling	1		3045-062
406	O-ring dia. 32,09 x 2,62 (incl. in pos. 405)	(1)		1331-133
407	Hexagon head screw M4 x 16 (incl. in pos. 405)	(1)		1413-320
	Electrical signal transmitter for
	V_i-slide position (optional)
410	Turning transmitter	1		3448-004
411	Driving lug	1		3044-020
413	Pointed screw M4 x 5	1		1413-211
413	Clamping pin dia. 1,5 x 12	1		1446-010
415	Screw for transmitter M3 x 8 (included in pos. 410)	4		1412-012
	Oil filter parts
450	Cover	1	1	3041-008
452	O-rmg dia 132,94 x 3,53	1	1	1331-093
453	O-ring dia 101,19 x 3,53	1	1	1331-083
455	Locking nut M10	1	1	1433-080
456	Cylinder screw Ml12 x 30	4	4	1413-386
458	Slay bolt	1	1	2111-129
459	Magnet	4	4	1517-022
460	Intermediate ring	4	4	3424-039
461	Elastomer ring	2	2	1334-012
470	Filter element	1	1	1517-121
471	Piug 1/4"	1	1	1343-025
472	Gasket ring dia. 21/14 x 2,0	1	1	1331-428
473	O-ring dia. 20,22 x 3,53	1	1	1331-019
480	Filter housing	1	1	3042-084
481	O-ring dia 183.74 x 3.53 (new production series)	1	1	1331-104
432	Cylinder screw M8 x 25	4	4	1413-357
483	Pointed screw M6 x 8	3	3	1413-230
	Ftow switch arrarngement
500	Terminal box	1	1	1554-001
505	Nippel	1	1	2314-106
506	Dowty ring 34,9/27,1 x 2.3	1	1	1331-433
507	Flow switch with ball	1	1	1553-024
508	Washer	1	1	2114-046
509	Gasket ring 19/14 x 1,5	1	1	2356-124
510	Spring	1	1	2144-041
511	Circlip (part of pos. 507)	1	1
	Compressor relief valve system
700-1	Back pressure independent safety valve BSV8, 18 bar	1	1	2416-202
700-2	Back pressure independent safety valve BSV8, 20 bar	1	1	2416-203
700-3	Back pressure independent safety valve BSV8, 21bar	1		2416-204
700-4	Back pressure independent safety valve BSV8, 22 bar	1		2416-224
700-5	Back pressure independent safety valve BSV8, 25 bar	1		2416-205
701-1	Connection line, POV 40, dia. 12	1		3014-014
701-2	Connection line, POV 50. dia. 12	1		3014-015
702	Cylinder screw M12 x 35	4	4	1413-387
703	O-ring dia. 82,14 x 3,53	1	1	1331-077
704-1	Main valve POV 40 including conneection pipe	1	1	3014-005
704-2	Main valve POV 50 including conneection pipe	1	1	3014-008
715	Cover	1	1	3013-177
716	Cylinder screw M16 x 40	4	4	1413-432
717	O-ring dia, 132,94 x 3,53	1	1	1331-093
721	Cylinder screw M12 x 30	4	4	1413-386
722	O-ring dia. 63,09 x 3,53	1	1	1331-071
725	Banjo coupling	1	1	1349-091
726	Al gasket, dia 24/13 x 1,5	1	1	2356-127
727	Reduced G 3/4" -G3/8" .	1	1	2312-038
730	Union nut G 1" - G 3/8".	1	1	2469-070
732	Al gasket, dia. 30/16 x 1,5	1	1	2356-137
	Temperature/pressure transducers
751	Pressure transducer, suction gas (PT1)	1	1	1373-249
752	Pressure transducer, oil after filter (PT3)	1	1	1373-271
753	Pressure transducer, oil before filter (PT4)	1	1	1373-271
755	Coupling 10-RL	2	2	1349-137
755	Elbow coupling 10-RL	1	1	1349-233
761	Temperature transmitter, compressor oil (TT6)	1	1	1373-281
752	Temperature transmitter,suction gas (TT7)	1	1	1373-282
765	Gasket ring DKA R 1/4	2	2	1349-135

	Spare parts survey for SAB 163 Mk3 unit

	The following list comprises all components that can be fitted on a compressor unit.

	From this list we have selected the components that are used on a particular unit and which are indicated on the piping diagram of this instruction manual. The position numbers on the piping diagram are a reference to the "Pos." columns of this list.

	The piping diagram is dedicated to the compressor number stated on page 1of this instruction manual.

	The components in the shaded areas are variable. This may be due to voltage, refrigerant, approved pressure ets.

	On ordering spare parts ft may be an advantage to recerve them in sets selected tor your specific compressor unit.

	A list of sets can had on request from SABROE's local representative.

	Pos.	Designation	Part no.
Regulating & Control device		UNISAB II
	PT1	Pressure transducer -1 - 9 bar	1373-249
	PT2	Pressure transducer -1 -25 bar	1373-271
	PT3	See PT2
	PT4	See PT2
	TT5/6/7	Temperature transducer PT100	1373-264
	GT8	Position transmitter (capacity)	3448-004
	GT9	See GT8
		UNIBAB II Frontpanel	1573-007
		1 CPU-module	1572-026
		1 Ralay print	1574-016
		1 EPROM extractor	1613-002
		1 EEPROM exctractor	1613-003
		1 EEPROM	1571-015.1
		3 Jumpers
		2 Fuses	1572-018
		1 Screw driver
Refrigerant system		Suction:
	20	O-ring dia 132,94 x 3,53	1331-093
		Set of gaskets for SCV100 (R717)	3184-079
		Set of gaskets for SCV150 (R22)	3184-081
	24
	34-35	Set of gaskets for SNV 8	2453-053
	47-48
		Oil separator, general:
	30	Sealing ring dia. 42/49 x 6,5	1349-213
	30	Heating rod, 250 V	3181-038
		Heating rod, 115V	3181-039
		Heating rod, 230	3181-040

	31	O-ring dia 52,07 x 2,62 (sight glass)	1331-140
		Sight glass	1226-017

	55	O-ring dia 329,57 x 5,33 (tor cover)	1331-184
	55	Oil separating element	1517-061

		Oil return:
	52	Nozzle valve	1364-151
	53	Sight glass	1226-014
	53	Gasket dia. 40.5/33 x 1.5	2356-144

		Discharge:
	204	Set of gaskets for SCV100	3184-079
		O-ring dia 120,4 x 3,53	1331-089

	22	Safety valves:
	28	DM 32/50
		Gasket, dia. 75/61 x 2.0	2356-220
		Gasket, dia. 109/95 x 2.0	2356-222
		O-rirg dia. 91.67 x 3.53 (house)	1331-060
		Conical seat for DN 32/50	1365-079
		Spring (for 25 Bar opening pressure)	1365-048
		DN 50/80
		Gasket, dia, 87/73 x 2.0	2356-221
		Gasket, dia, 120/106 x 2.0	2356-223
		O-ring dia. 117.07 x 3.53 (house)	1331-088
		Conical seal for DN 50/8O	1365-080
		Spring (for 25 Bar opening pressure)	1365-050
Oil system		Flange connection, oil tube
		Gasket, dia 75/61 x 2,0	2356-220
		O-ring dia 59.92 x 3.53 (compr.)	1331-071
		Oil by-pass (at pump)
		Gasket, dia 131/95 x 1,5 (non-return valve)	2356-104
		O-ring dia 40,94 x 2,62 (non-return valve)	1331-298
		Pressure build up for capacity reg.
		Non-return valve 18,1 bar	1364-009
		Non-return valve 10,02 bar	1364-008
		Oil pump
	63	Shaft seal complete	1332-192
	63	O-ring dia 44,12 x 2,62 (cover for pump)	1331-146
	64-65	Set of gaskets for SVA 15	2453-022
	60-62	Set of gaskets for SVA 32
	61	Fitler element 150	2464-233
	61	O-ring dia 44.04 x 3,53	1331-022
	61	O-ring dia 36,09 x 3,53	1331-029
	61	O-ring dia 13,94 x 2,62	1331-014
Capacity regulation	46	Thermostatic three-way valve, type RT5
		O-ring, Neoprene	1331-383
		Thermo element, 48'C	1365-005
	70	Solenoid valve block
		Valve housing EVM (NC)	1372-335
		Gasket set for EVM (NC/NO)	1336-024
		Coil 10 W 220 V 50/60Hz	1372-537
		110 V 50/60Hz	1372-538
		240 V 50Hz	1372-539
	71	Solenoid valve
		Valve housing EVM (NO)	1372-425
		Gasket set for EVM	1336-024
		Throttle valve
	72	Gasket set 6F	1377-210
	73	Solenoid valve:
		See pos.70
	74	Solenoid valve
BLI Oil cooling	80-84	Gatket set for SVA 15-20	2453-022
	81	Filter FA15:
		(When TEAT 28 is selected)
		Gasket set for FA15	1377-078
		Repair kit for FA15	1377-250

		Filter FA20:
	81	(When TEAT 85 is setected)
		Gasket set for FA20	1377-079
		Repair kit for FA20	1377-251

	82	Solenoid valve EVRA15
		(whenTEAT 20 is selected)
		Gasket set (for EVRA15)	1377-093
		Repair kit (for EVRA 15)	1377-099
		Coil 10W 220 V 50/60 Hz
		110 V 50/60 Hz See pes 70
		240 V 50 Hz
	82	Solenoid valve EVRA20
		(when TEAT 85 is selected)
		Gasket set (for EVRA 20)	1377-094
		Repair kit (for EVRA 20)	1377-069
		Coil 10W 220 V 50/60 Hz
		110 V 50/60 Hz See pes 70
		240 V 50 Hz
	83	Injection valve TEAT 20
		Nozzle insert 20-8	1371-203
		Nozzle inset 20-12	1371-204
		Nozzle insert 20-20	1371-206
		Thermal part 35-65 deg. C	1371-255
		Thermal part 55-95 deg. C	1371-253
	83	Injection valve TEAT 85
		Nozzle insert 85-33	1371-207
		Nozzle Insert 85-55	1371-208
		Nozzle insert 85-85	1371-209
		Thermal part 35-65 deg. C	1371-257
		Thermal part 55-95 deg. C	1371-250
	83	Injection valve PMFL 80
		Gasket set	1377-040
		Piston rod	1377-086
Compr. connections		Spare parts set for coupling S952 size 262
		Sheets, bolts, nuts & slices	1524-125
		Spacer bushing	1526-003
		Stop screw M 10 x 10	1413-250
		Combination wrench 9/16"	Compr.
		Box wrench 9/16"	Tools
		Alignment motor - compressor
		Discs (motor up to IEC 280)	2221-067
		Discs ( motor from IEC 315)	2221-076
		Tools	3183-104

Tools for compressor SAB 163 Mk3

Line no. A401 = Normal set (part no. 3083-047)

Line no. A402 = Extendet set (part no. 3083-049 incl. 3083-048)

Line no. B401 = Tools for alining the coupling (part no. 3183-104)

Line no. B402 =Tools tor shaft seal removal, oil pump (part no.3083-160)

Tools no.	Designation	Part no.	A401	A402	B401	B402
1	Pullar for bearings	3083-131	1	1
2	Thrust ring for the puller, female :	3083-130	1	1
3	Thrust ring for the puller, male	3083-054	1	1
4	Tools for fitting the bearings	3083-058	1	1
5	Ring for the puller	3083-053	1	1
6	Tools for pressing out the rotors	3083-132	1	1
7	Tools for fitting the bearings	3083-133	1	1
8.1	Retaining cup formate rotor	3083-102	1	1
8.2	Retaining cup for female rotor.	3083-103	1	1
9	Tools for dismounting the bearings	3083-052	2	2
10	Thrust washer	3083-129	1	1
11	Locking tool for rotor	3083-128	1	1
12	Bearing dia 42/25 x 11	1512-015	1	1
20.1	Threaded pins M10 x 160	2112-129	4	4
20.2	Threaded pin M16 x 325	2112-151	1	1
21.1	Hexagon head screw M20 x 120	1424-298	1	1
21.2	Hexagon head screw M10 x 130	1424-203	4	4
22.2	Socket cap screw M8 x 35	1413-359	1	1
22.3	Socket cap screw M8 x 120	1413-314	1	1
22.4	Socket cap screw M10 x 25	1413-371	4	4
22.6	Socket cap screw M16 x 50	1413-434	1	1
22.7	Hexagon head screw M16 x 130	1424-113	1	1
23.1	Nuts M8	1432-063	2	2
23.2	Nuts M10	1432-064	4	4
23.3	Nuts M16	1432-067	1	1
24.2	Washer dia. 45/17 x 5	3083-114	4	4
25	Guide pin M16 x 300	2112-147	2	2
30	Tools for adjusting the bearings	3083-101	1	1
31	Special screw for adjusting the bearings	3083-100	1	1
32.2	Eye bolt M16	1427-156	1	1
33	Alignment device for coupling	3133-104			1
34	Feeler gauge	1622-050			1
36	Tools for shaft seal removal, oil pump Consists of:
33,1	Puller for shaft seal, oil pump	3083-157				1
36,2	Cap screw M10 x 75	1424-201				1
36,3	Threaded pin M8 x 150	3083-156				3
36,4	Nuts M8	1432-063				3
36,5	Punch dia. 18 x 80	3083-158				1
36,6	Punch dia. 22/16,5 x 100	3083-159				1
40.1	Torque wrench (Ratchet) 5 - 50 Nm 1/2"			1
40.2	Torque wrench 40-200 Nm (14 x 18)			1
42	Extention 1/2°			1
43	Converter for torque wench(14x18) - 1/2"			1
44.2	Hexagon bit adaptor 1/2" - 5mm			1
44.3	Hexagon bit adaptor 1/2" - 6mm			1
44.4	Hexagon bit adaptor 1/2" - 8mm			1
44.5	Hexagon bit adaptor 1/2" - 10mm			1
44.6	Hexagon bit adaptor 1/2" - 14mm			1
45	Box spanner insert 1/2" - 19mm			1
45.2	Box spanner insert 1/2" - 30mm			1
45,3	Box spanner insert 1/2" - 36mm			1
45.4	Box spanner insert 1/2"-9/16"			1
46	Open end spanner (14 x 18) - 24mm			1
50.1	Combination spanner 17mm	1612-276		1
50.2	Combination spanner 9/16"			1
51.1	Allen key for socket cap screw 3mm	1612-395		1
51.2	Allen key for socket cap screw 5mm	1612-397		1
51.3	Allen key for socket cap screw 6mm	1612-398		1
51.4	Allen key for socket cap screw 8mm	1612-399		1
51.5	Allen key for socket cap screw 10mm	1612-401		1
51.6	Allen key for socket cap screw 14mm	1612-400		1
52	Magnetic Fixture for dial indicator			1
53	Dial indicator			1
54.1	Retaining ring plier			1
54.2	Retaining ring plier			1
55.1	Hammer	1612-012		1
55.2	Plastics hammer	1612-042		1
56	Steel punch 10 mm			1
57	Plier for driving pin	1612-190		1

List of parts for SAB 202


List of parts for SAB 202
Relevant drawing 0661-855

Pos	Designation	No	Part no
	Complete compressor LF, aut. Vi		4161-059
	Complete compressor LF, man. Vi		4161-060
	Complete compressor LM, aut. VI		4161-061
	Complete compressor LM, man, Vi		4161-062
	Complete compressor SF, aut. VI		4161-063
	Complete compressor S F, man. Vi		4161-064
	Complete compressor SM, ant, Vi		4161-065
	Complete compressor SM, man. Vi		4161-066
	Compressor housing
10-1	Compressor housing (L)	1	3011-009
10-2	Compressor housing (S)	1	3011-019
	Bearing cover at suction end
20-1	Bearing cover, female drive	1	3013-089
20-2	Bearing cover, male drive	1	3013-110
21	O-ring dia. 430,66 x 3,53, neoprene	1	1331-117
22	Innar sleeve, INA IR dia. 17/20 x 16	2	1514-018
23	Washer dia. 25/16.5 x 4	4	2114-047
24	mreaded plug with cottar 1/2	1	1343-027
25	Dowty ring 025	1	1331-430
26	Cylindrical screw M16 x 60	10	1413-436
27	Cylindrical screw M 16 x 30	2	1413-429
28	Cylindrical screw Ml 6 x 180	8	1413-428
30	Hose connection	1	1345-143
	Bearing cover at ditcharge end
40	Thrust cover/capacity regulating cylinder	1	3013-150
41	Cylinder screw M16 x 60	20	1413-436
42	Washer dia. 35/16,5 x 4	4	2114-047
43	O-ring dia. 151,93 x 3,53, neoprene	1	1331-099
44	Adjusting screw	a	2111-128
45	Locking screw M6 x 10	4	1413-231
46	Cross bar for bearing adjustment	1	3083-137
47	Cylinder screw M12 x 30	6	1413-366
48	Inner sleeve, INA IR dia 17/20 x 16	2	1514-018
49	O-ring dia. 13,94 x 2,62	1	1331-014
	Cover for capacity regulating cylinder
60	Cover for capacity cylinder	1	3013-197
61	O-ring dia. 142,47 x 3,53 - neoprene	1	1331-096
62	Cylinder screw M12 x 35	4	1413-387
	Housing for capacity indicator
70	Housing for capacity indicator	1	3045-002
71	Cylinder screw M6 x 30	4	1413-343
72	Cover for capacity indicator	1	3045-003
73	Cylinder screw M6 x 50	4	1413-347
74	O-ring dia. 98.02 x 3,53, neoprene	1	1331-081
75-1	Glass for indicator (L)	t	3045-050
75-2	Glass for indicator (S)	1	3045-049
	Rotors
110-1	Set of rotors tor SM	1	3024-102
110-2	Set of rotors tor SF	1	3024-097
110-3	Set of rotors for LM	1	3024-103
110-4	Set of rotors for LF	1	3024-095
111	Journal bearing	4	1515-031
112	Retaining pin for journal bearing dia, 5 x 45	4	1446-033
113	Cylinder screw M6 x 45	8	1413-340
114	Thrust washes	2	3021-029
115	Cylinder screw M16 x 45	2	1413-433
132	Four point ball bearing dia. 70/150 x 35	2	1513-040
133	Set of shims dia. 128/150 for adjusting the clearance between the rotor and outlet port. Comprising: 1 off thickness 5,60 mm	2	3021-043
	1 - 5,65 mrr
	1 - 5,70 mm
	1 - 5,75 mm
	1 - 5,80 mrn
	1 - 5,85 mm
	1 - 5,90 mm
134	Balance piston. drive rotor	1	3025-052
135	Spacer ring, drive rotor	1	3025-035
136	Retaining ring 4 x 10	1	1446-012
137	Balance piston, driven rotor	1	3025-034
138	Spacer ring, driven rotor	1	3025-036
139	Retaining pin 5x16	1	1446-021
	DIscharga ports
140-1	Discharge port for male rotor .	1	3031-031
141-1	Discharge port for female rotor	1	3031P032
142	Cylinder scraw M8 x 190	6	1413-309
143	Washer for discharge port dia. 16,5 /8,2 x 10	6	2114-045
144	Cylinder screw M6 x 30	2	1413-343
145	Pointed screw M10 x 35 - inside adjustment	2	1413-255
146	Locking screw M10 x 10 - inside adjustment	2	1413-253
147	Locking screw M10 x 10 - outside adjustment	2	1413-253
148	Pointed screw M10 x 20 - outside adjustment	2	1413-032
149A	Blank of screw 3/8" - outside adjustment	2	1343-026
149B	Gasket - outside adjustment	2	1331-427
	Parts for adjusting rotors
153	Inner cover	2	3021-030
154	O-ring dia. 142,47 x 3,53	2	1331-096
155	Cylindrical steel roll 8H 11 x 8	S	1514-019
	Shaft seal
160A	Shaft seal collar 1
160B	Shaft saal seat 1
160C	O-ring for shaft seat collar 1	1	3084-557
160D	O-rlng for shaft saal seat 1
160E	Pointed screw 3
161	Retaining pin for shaft seal seat dia. 3 x 5	1	1446-005
162	Spirolox ring (oil thrower)	1	1437-294
163-1	Cover, F	1	3013-100
163-2	Cover, M	1	3013-102
164	O-ring dia, 132,94 x 3,53, neoprene	1	1331-093
165-1	Cover for shaft seal, F	1	3013-099
165-2	Cover for shaft seal, M	1	3013-101
166	O-ring dia, 158,34 x 3,53	1	1331-100
167	Cylinder screw M12 x 35	8	1413-387
168	Hose connection branch 1 /4°	1	1345-143
169	Clear plastic hose	1	1241-190
	Suction filter
170	Suction filter	1	3042-075
	Adjusting system for V_i-slide, AUT
352	Screw for transmitter M3 x 8 (included in pos. 410)	(4)	1412-012
371	Sealing ring OD 70	1	1332-126
372	Attachment for pin	1	3044-035
380	Cover tor aut. Vi	1	3013-196
381	O-ring dia. 101,19 x 3,53, neoprene	1	1331-083
382	Cylinder screw M12 x 35	4	1413-387
384	Attachment for sealing ring	1	3044-034
385	Cylinder screw M4 x 16	2	1413-320
386	Cylindrical pin dia. 6 x 16	2	1445-076
387	Cylinder screw M6 x 12	1	1413-339
390	Spindle aut. V_i	1	3044-063
393	Ball baaring 6202	1	1511-012
395	Driving disk	1	3044-021
396	Cylinder screw M4 x 12	1	1413-318
400	Attachment tor transmitter	1	3044-064
401	Cylinder screw M6 x 80	4	1413-307
402	Cover ring for transmitter	1	3045-009
403	Cylinder screw M4 x 10	4	1413-319
405	Magnetic coupling	1	3045-062
406	O-ring dia. 32,99 x 2,62 (incl in pos. 405)	(1)	1331-133
407	Hexagon head screw M4 x 16 (inc. in pos. 405)	(1)	1413-320
410	Turning transmitter	1	3448-004
411	Driving lug	1	3044-020
412	Pointed screw M4 x 5	1	1413-211
413	Clamping pin dia. 1,5 x 12	1	1446-010
	Adjusting system for V_i-slide, MAN
180	Spindle man. Vi	1	3044-052
181	Cover for man. Vi	1	3013-093
182	Sealing washer for slide stop	1	3044-014
183	Sealing ring	1	1331-503
184	O-ring dia. 44,04 x 3,53, neoprene	1	1331-065
185	Retainer for bearings	1	3044-033
186	Axial ball bearing dia. 42/25 x 11	2	1512-015
187	Locking plate	1	2114-043
188	Cylinder screw M6 x 12	1	1413-339
189	Thread washer	1	3044-073
195	Cylinder screw M4 x 30	2	1413-325
196	Cylinder screw M6 x 35	3	1413-344
197	O-ring dia. 101,19 x 3,53	1	1331-083
198	Cylinder screw M12 x 35	4	1413-387
	Vi-slide
190-1	Slide stop, S	1	3043-131
190-2	Slide stop, L	1	3043-130
191-1	Spring for Vi-slide,L	1	2144-042
191-2	Spring for Vi-slide,S	1	2144-043
192	Cylinder screw M 10 x 25	1	1413-371
	Capacity regulating slide
200-1	Slide for L	1	3043-113
200-2	Slide for S	1	3043-125
201	Piston part inner	1	3043-138
202	Piston part outer	1	3043-139
203	O-ring dia. 40,87 x 3,53, neoprene	1	1331-064
204	Sealing ring dia. 150	1	1332-133
206	Slotted nut KM8	1	1514-200
207A-1	Piston rod for L	1	3043-140
207A-2	Piston rod for S	1	3043141
207B	Bushing tor indicator spindle Included in pos. 207A	1	3045-046
207C	Cylindrical pin dia. 6 x 16 Included in pos. 207A	1	1445-076
207D	Spirolox-ring Inducted in pos. 207A	1	1437-291
207E	Steel ball 3/8" Included in pos. 207A	1	1514-158
208	Locking plate for slotted nut	1	1514-070
209	Tape bearing	2	2132-100
311	Cap torew M20 x 60	1	1424-289
313	Clamp	1	3042-054
	Spindle for copacity indication
210	Spindle tor capacity indication	1	3045-059
216	Magnetic coupling	1	3045-061
217	O-ring dia. 44,12 x 2,62 (incl. in pos. 216)	(1)	1331-146
218	Hexagon head screw M4 x 16 (Incl. in pos. 216)	(1)	1413-320
219	Hexagon head screw M4 x 20 (ind. in pos. 216)	(2)	1413-322
	Capacity indication
221	Indication disk	1	3045-001
223	Socket cap screw M4 x 10	1	1413-319
224	Backing ring 105/90 x 1,6	1	2356-155
226	Locking washer DC 15/8,4	1	1437-054
227	Locking washar DC 8/4,3	1	1437-060
350	Position transmitter	1	3448-004
351-1	Indicator glass, L (replacing pos. 75-1 when transmitter)	1	3045-048
351-2	Indicator glass, S (replacing pos. 75-2 whentransmitter)	1	3045-047
352	Screw for transmitter M3 x 8 (incl. in pos. 350)	(4)	1412-012
	Non return valve
	Non return valve complet		3042-172
252	O-ring dia. 253,37 x 5,33, neoprene	1	1331-181
253	Intermediate flange	1	3013-288
255	Valve housing	1	3042-127
256	Spindle guide	1	3042-125
257	Retainer	1	3042-126
258	Hexagon head screw M8 x 120	3	1413-314
259	Valve cone	1	3042-123
260	Spindle	1	3042-124
261	Spring	1	1523-033
262	Tape bearing dim 10 x 1 x 46	1	2132-114
263	Tape bearing dim 10 x 1 x 105	t	2132-096
264	Hexagon head screw M16 x 75	8	1424-108
265	Countersunk socket cop. screw M12 x 25	1	1413-115
266	Hexagon bead scraw M12 x 30	2	1413-386
267	Shaft nut KM9 - M45	1	1514-201
268	Seeger ring dia. 14 x 1,0, DIN 471	1	1437-207
	Oil injection
316	V-joint 22-RL	1	1349-153
317	Check valve RVS	1	1364-163
318	O-ring dia. 33,05 x 1,78	1	1331-123
319	Valve seat	1	3042-077
	External oil piping
320-1	Pipe sat (L)	1	3049-026
320-2	Pipe set (S)	1	3049-029
321	Pipe clamp dia. 3 x 12	1	2532-012
	Oil filter
450	Oil filter cover	i	3041-008
452	O-ring dia. 132,94 x 3,53, neoprene	1	1331-093
453	O-ring dia. 101,19 x 3,53, neoprene	1	1331-083
455	Lock nut M10	1	1433-030
456	Cylinder screw M12 x 35	4	1413-387
458	Stay bolt for magnet	1	2111-127
459	Magnets for oil filter	4	1517-022
460	Intermediate ring	4	3424-039
461	Rubber ring	2	1334-012
462	Plug 1/4"	2	1343-025
463	Dowty ring dia. 20,57 x 13,74	2	1331-428
470	Oil filter cartridge	1	1517-015
475	O-ring dia. 63,9 x 3,53	1	1331-071
476	Cylinder screw M 12 x 30	4	1413-386
	Oil flow swich
500	Terminal box	1	1554-001
501	Cover for flow switch	1	3041-004
502	O-ring dia. 132,94 x 3,53, nroprere	1	1331-093
505	Nipple tor ftow switch o	1	2314-106
506	Dowty ring	1	1331-433
507	Flow switch with ball	1	1553-024
508	Washer	1	2114-046
509	Gasket dia. 19/14 x 1,5	1	2356-124
510	Spring	1	2144-041
511	Circlip (included in pos. 507)	1
512	Cylinder screw M12 x 35	4	1413-387
	Plugging
520	Plug 1/2"	1	1343-027
521	Dowty ring 025	1	1331-430
525	Plug 3/4"	1	1343-028
526	Dowty ring 027	1	1331-433
530	Plug 1/4"	1	1343-025
531	Gasket ring 19/14 x 1,5	1	2356-124
	Economizer inlet
600	Eco-plug	1	3013-111
601	Cylinder screw M12 x 30	4	1413-386
602	Cylinder screw M8 x 30	2	1413-358
603	O-ring dia. 53,57 x 3,53, neoprene	1	1331-058
	Relief valve
700-1	Back pressure independent valve. BSV 8-18 bar	1	2416-202
700-2	Back pressure independent valve. BSV 8-22 bar	1	2416-224
	Pilot operated valve
701-A	Connection line for POV 50	1	3049-032
701-B	Connection line for POV 60	1	3049-033
702-A	Cylinder screw M12 x 25	4	1413-385
702-B	Cylinder screw M 12 x 30	4	1413-388
703-A	O-ring dia. 63,09 x 3,53	1	1331-071
703-B	O-ring dia. 88,49 x 3,53	1	1331-079
704-A	Pilot operated valve, POV 50 (for R717)	1	2417-046
704-B	Pilot operated valve, POV 80 (for R22 and HCF^,s)	1	2417-058
	Cover for main valve
705-A	Cover for POV 50	1	3013-125
705-B	Cover for POV 80	1	3013-163
706	Cylinder screw M16 x 40	8	1413-432
707	O-rlng dia. 253.37 x 5,33	1	1331-181
	Connection between compr. discharge side and suction side
710-A	Manifold for POV 50	1	3013-124
710-B	Man (fold tor POV 80	1	3013-157
711-A	O-ring dia. 85,32 x 3,53	1	1331-078
711-B	O-ring dia. 86,49 x 3,53	1	1331-079
712-A	Cylinder screw M12 x 110	3	1413-406
712-B	Cylinder screw M12 x 30	4	1413-386
715-A	Cover (for POV 50 only)	1	3013-125
716	Cylinder screw M16 x 40	4	1413-432
717	O-ring dia. 164,69 x 3,53	1	1331-101
720-A	Pipe conneclion for POV 50	1	3014-002
720-B	Pipe connection for POV 80	1	3013-166
721-A	Cylindar screw M12 x 30	8	1413-386
721-B	Cylinder screw M12 x 40	4	1413-388
722-A	O-ring dia. 75,79 x 3,53	2	1331-075
722-B	O-ring dia. 88.49 x 3,53	1	1331-079
	Releif valve connections
725	Stud coupling A-12 RL	1	1349-053
726	Al-gasket dia.24/13 x 1,5	1	2356-127
727	Reducer G3/4 - G3/8	1	2312-038
729	Elbow coupling VB 12-RL	1	1349-210
730	Union nut G1	1	2313-017
731	Threaded nipple G3/8	1	2311-065
732	Al-gastet dia.30/16 x 1,5	1	2356-137
733	Dowty ring 023	1	1331-427
	Signal trantducers
751	Pressure transducer, PT1	1	1373-249
752	Pressure transducer, PT3	1	1373-271
753	Pressure transducer, PT4	1	1373-271
755	Stud coupling	2	1349-137
756	Stud elbow	1	1349-233
761	Temperature transmitter, TT6	1	1373-264
762	Temperature transmitter, TT7	1	1373-264
765	Gasket ring	2	1349-135
766	Reducer G1/2-G1/4	1	1349-077

S=L/D 1.7 M=Male drive

L=L/D 2,2 F=Female drive

Spare parts survey for SAB 202 unit

The following list comprises all components that can be fitted on a compressor unit.

From this list we have selected the components that are used on a particular unit

and which are indicated on the piping diagram of this instruction manual.

The position numbers on the piping diagram are a reference to the "Pos." columns of this list

The piping diagram is dedicated to the compressor number stated on page 1 of this

instruction manual.

The components in the shaded areas are variable. This may be due to voltags, refrigerant,

approved pressure etc.

On ordering spare parts it may be an advantage to receive them in sets selected

for your specific compressor unit.

A list of sets can had on request from SABROE's local representative.

Pos.	Designation	Part no.
	Regulating & Control device
	UNISAB Il
PT1	Pressure transducer -1 - 9 bar	1373-243
PT2	Pressure transducer -1-25 bar	1373-271
PT3	Pressure transducer -1 - 25 bar	1373-271
PT4	Pressure transducer -1 -25 bar	1373-271
TT5-6-7	Temperature transducer PT100	1373-252
TT5-6-7	Temperatura transducer PT100	1373-264
	(Avaible after 97.01.20)
GT6	Position transmittar (capacity)	3448-004
GT9	Position transmitter	3448-004
	UNISAB II Frontpanel	1573-007
	1 CPU-Module	1572-026
	1 Relay print	1574-016
	1 EPROM extractor	1613-002
	1 EEPROM extractor	1613-003
	1 EEPROM	1571-015
	3 Jumpers
	2 Fuses	1572-018
	1 Screw driver
	Refrigerant system
	Suction:
20	O-ring dia. 253,37 x 5,33	1331-181
	Set of gaskets for SCV 125 (M R717)	3184-080
	Set of gaskets for SCV 150 (M R22/F R717)	3184-081
	Set of gaskets for SCV200 (F R22)	3184-081
24
34-35	Sel of gaskets for SNV 8	2453-053
47-48
	Oil separator, general:
22	O-ring dia. 164,69 x 3,53 (disch. flange)	1331-101
30	Sealing ring dia. 42/49 x 6,5	1349-213
30	Heating rod, 250V	3181-038-1
	Heating rod, 115V	3181-039-1
	Heating rod, 230V	3181-040
31	O-ring dia. 52,07 x 2,62 (Sight glass)	1331-140
	Sight glass	1226-017
55	O-ring dia. 329,57x5,33 (for cover)	1331-184
	Oil separating element	1517-079-2
	Oil return:
52	Nozzle valve	1364-151
53	Sight glass	1226-014
53	Gasket dia. 40,5/33 x 1,5	2356-144
	Discharge:
204	Set of gaskets for SCV 100 (M)	3184-079
	Set of gaskets for SCV 100 (F)	3184-097
	Safety valves:
28	DN 40/65
	Gasket dia. 75/61 x 2,0	2356-220
	Gasket dia. 109/95 x 2,0	2356-222
	O-ring dia. 91,67 x 3,53 (house)	1331-080
	Conical seal for DN 40/65	1365-079
	Spring (for 25 bar opening pressure)	1523-027
28	DN 50/80
	Gasket dia. 87/73 x 2,0	2356-221
	Gaskat dia. 120/106 x 2,0	2356-223
	O-ring dia. 117,07 x 3,53 (house)	1331-088
	Conical seal for DN 50/80	1365-080
	Spring (for 25 bar opening pressure)	1365-050
28	DN 65/100
	Gasket da. 109/95	2356-222
	Gasket dia. 149/129	2356-224
	O-ring dia. 151,99 x 3,53 (house)	1331-099
	Conical seal for DN 65/100	1365-081
	Spring (for 25 bar opening pressure)	1523-035
28	DN 80/125
	Gasket dia. 120/106	2356-223
	Gasket dia. 175/155	2356-228
	Gasket for safety valve house DN 80/125	1365-082
	Conical seal for DN 80/125	1365-075
	Spring (for 25 bar opening pressure)	1523-036
	Water-cooled oil cooler OWSG
33	OWSG 16xx
	Gasket dia. 270/150 x 5,0	2355-171
	Gasket dia. 107/61 x 2,0	2357-014
	Gasket dia. 36/28 x 1,5	2356-141
33	OWSG 21xx
	Gasket dia. 310/205 x 5,0	2355-172
	Gasket dia. 142/90 x 2.0	2356-269
	Gasket dia, 36/28 x 1,5	2356-141
	O-ring dia. 34,52 x 3,53	1331-028
33	OWSG 27xx
	Gasket dia.370/255 x 5,0	2356-173
	Gasket dia.162/115 x 2,0	2356-276
	O-ring dia. 34,52 x 3,53	1331-028
	External oil filter type BGAH
39	Filter element	1517-015
	O-ring dia. 169,3 x 5,7 (cover)	1331-226
	O-ring dia. 130,2 x 5,34 (insert)	1331-169
	O-ring dia. 109,2 x 5,7 (element)	1331-225
	O-ring dia. 62,14 x 3,53 (collar)	1331-077
	External oil filter type OF2108
39	Filter element	1517-015
	O-ring dia. 170,82 x 5.33 (cover)	1331-175
	O-ring dia. 130,2 x 5,33 (insert)	1331-169
	O-ring dia. 109,2 x 5,70 (element)	1331-225
38-42	Set of gaskets for SCV 50	3184-077
	Flange connection, oil tube
	Gasket dia. 87/73 x 2,0	2356-221
	O-ring dia. 63,09 x 3,53 (compr.)	1331-071
	Oil by-pass (at pump)
210	Gasket dia. 140/105 x 1,5 (non-return valve)	2356-106
69	O-ring dia. 50,40 x 3,53 (non-return valve)	1331-300
	Thermostatic three-way valve, type RT6
46	O-ring, Neoprene	1331-384
	Thermo element (48 deg. C)	1365-084
70	Solenoid valve
	Valve housing EVM (NC)	1372-335
	Gastet set for EVM	1336-024

	Coil 10 W 220 V 50/60 Hz	1372-537
	110 V 50/60 Hz	1372-538
	240 V 50 Hz	1372-539

71	Solenoid valve
	Valve housing EVM{NO)	1372-287
	Gasket set for EVM	1336-024-02

	Coil 10 W 220 V 50/60 Hz	1372-537
	110 V 50/60 Hz	1372-538
	240 V 50 Hz	1372-539

	Throttle valve	1364-151
73	Solenoid valve - see pos.70

74	Solenoid valve
	Valve housing EVM (NO) - see pos.71	027B1130

80-84	Gasket set for SVA 15-20	2453-022
81	Filter FA15 - When TEAT 20 is selected
	Gasket set for FA15	1377-078
	Repair kit for FA 15	1377-250
81	Filter FA20 - When TEAT 85 is selected
	Gasket set for FA20	1377-079
	Repair kit for FA20	1377-251
82	Solenoid valve EVRA15 - When TEAT 20 is selected
	Gasket set (for EVRA 15)	1377-093
	Repair kit (for EVRA15)	1377-099
	Coil 10 W 220 V 50/60 Hz	1372-537
	110V 50/60 Hz	1372-538
	240V 50 Hz	1372-539
82	Solenoid valve EVRA20 - When TEAT 20 is selected
	Gasket set (for EVRA20)	1377-094
	Repair kit (for EVRA20)	1377-069
	Coil 10 W 220 V 50/60 Hz	1372-537
	110 V 50/60 Hz	1372-538
	240 V 50 Hz	1372-539
83	Injection valve TEAT 20
	Nozzle insert 20-8	1371-203
	Nozzle insert 20-12	1371-204
	Nozzle insert 20-20	1371-206
	Thermal part 35-65 deg. C	1371-255
83	Injection valve TEAT 85
	Nozzle insert 85-33	1371-207
	Nozzle insert 85-55	1371-208
	Nozzle insert 85-85	1371-209
	Thermal part 35-65 deg. C	1371-257
	Ecomomizer - ECO - DN 40
97	O-ring dia. 59,92 x 3,53 (tlange)	1331-070
120	Gasket set for SCH 40	3184-112
133	Gasket set for STA 40 (2464,158)	2453-030
133	Filter 250	2464-212
	Ecomomizer - ECO - DN 50
97	O-ring dia. 59,92 x 3,53 (flange)	1331-070
120	Gasket set for SCH 50	3184-112
133	Gasket set for STA 50 (2464,166)	2453-030
133	Fiiter 250	2464-212
	Spare parts set for coupling S952 size 312
	Sheets, bolts, nuts & slices	1524-126
	Spacer bushing	1526-004
	Stop screw M 10 x 10	1413-250
	Combination wrench 5/8"	Compr. tools
	Box wrench 5/8"	Compr. tools
	Alignment motor - compressor
	Disc (motor up to IEC 280)	2221-067
	Disc (motor from IEC 315)	2221 -076
	Tools	3183-104

Tools for compressor SAB 202

Line no. A401 = normal set 3083-184

Line no. A402 = Extended set 3083-185

Line no. B401 = Toois for aligning the coupling 3163-105

Line no. B402 = Tools for shaft seal removal, oil pump 3083-160

Tools no	Designation	Part no.	A401	A402	B401	B402
1	Thrust plate for puller 40 x 20 x 200	3083-173	1	1
a	Puller for bearings 40 x 20 x 145	3083-172	1	1
3	Threaded pins M12/M6 x 200	3083-171	2	2
4	Threaded pin M14, Koko	1427-037	1	1
5	Thrust plate for mounting the bearings 40 x 15 x 150	3083-181	1	1
6	Washer for mounting the bearings dia. 130/17 x 15	3083-182	1	1
7	Threaded pin M16 x 200	3083-180	1	1
8	Long nut M16 x 50	1432-191	1	1
9.1	Nut M16	1432-067	1	1
9.2	Nuts M12	1432-065	2	2
10	Mounting bushing for ball bearing, inner ring	3083-174	1	1
11	Guide pins for suction- and disharge cover M16 x 300	3083-164	2	2
12	Punch for locking the rotors	3083-183	1	1
13	Plate for locking the rotors 40 x 15 x 200	3083-179	1	1
14	Plate for dismounting the rotors 60 x 25 x 360	3083-177	1	1
15	Bushing dia.25/17 x 15	3083-178	2	2
16.1	Cap screw M20 x 120	3083-176	1	1
16.2	Cap screw M16 x 40	3083-175	1	1
17.1	Socket cap screws M16 x 60	1413-436	2	2
17.2	Socket cap screws M16 x 40	1413-432	2	2
17.3	Socket cap screws M6 x 16	1413-340	2	2
18	Washer dia 20/17 x 3	1436-001	1	1
19	Threaded pin M 16 x 250	3083-168	1	1
20	Thrust plate 50 x 20 x 270	3083-167	1	1
21	Pipe pieces dia. 25.9/21.3 x 187	3083-170	2	2
22	Threaded pins M 12 x 275	3083-169	2	2
23	Gauge dia. 62/17 x 51	3083-166	1	1
24	Spring dia. 50 x 9.5	2142-060	1	1
25.1	Nuts with collar M12	1432-170	2	2
25.2	Nut with ooiiar M16	1432-171	1	1
26	Plate with M12 nut 20 x 6 x 100	3083-163	1	1
27-1	Socket cap screw key with handle 5 mm	1612-391	1	1
27-2	Socket cap screw with handle M12 x 180	3083-165	1	1
2B	Eye-bol M12	1427-150	1
30	Alignment device for coupling	3183-105			1
31	Feeler gauge (incl in3183-105)	1622-050			1
32	Tools for shaft seal removal, oil pump	3083-160				1
	Consists of:
	Puller for shaft seal, oil pump	3083-157				1
	Cap screw M10 x 75	1424-201				1
	Threaded pin M8 x 150	3083-156				3
	Nuts M8	1432-063				3
	Punch dia. 18 x 80	3083-158				1
	Punch dia. 22/16.5 x 100	3083-159				1
40.1	Combination spanner 19mm			1
40.2	Combination spanner 24mm			1
40.3	Combination spanner 30mm			1
40.4	Combination spanner 36mm			1
41	Open end spanner 19/22mm			1
42.2	Hexagon bit adaptor 1/2"- 5mm			1
42.3	Hexagon bit adaptor 1/2" - 6mm			1
42.4	Hexagon bit adaptor 1/2" -10mm			1
42.5	Hexagon bit adaptor 1/2'"-14mm			1
42.6	Hexagon bit adaptor 1/2" -17mm			1
43	Rachet spanner			1
44.1	Torque wrench 10-60 Nm			1
44.2	Torque wrench 50-300 Nm			1
45	Pointed screw M 16 x 20	1413-262	2	2
46	Box spanner insert 1/2"-36mm			1
47	Hook spanner KM8			1
48.1	Extension (long)			1
48.2	Extension (short)			1
49	Puller, kukko 10-20			1
50	Dial indicator			1
51	Magnetic fixture for dial indicator			1
52.1	Retaining pliers J2			1
52.2	Retaining pliers A1			1